SEVERIN KS-9782 Instrucciones De Uso página 15

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 39
∙ If the unit is installed next to a wall, a minimum lateral
distance of 225 mm is necessary, so that the doors can open
wide enough for the drawers to be taken out.
Set-up dimensions
Ventilation
The heated air around the rear of the unit must be able to
circulate freely. Therefore, ensure that the air circulation behind
the unit is not obstructed.
Caution: Ensure at all times that the rear ventilation
openings around the top cover are not obstructed.
Reversible door
If required, the door may be reversed, i.e. from right-hinged (default
installation) to left-hinged.
Warning: Always disconnect the unit from the mains before
any maintenance or repair work is carried out.
Before you get started, please note the following:
∙ Always ensure that the correct number of washers is used
on the hinge bolts.
∙ So that the doors can close tightly against the frame, take
the utmost care that they are properly aligned during re-
assembly.
1.
Remove the four covers c from the housing and inside of
the door.
2.
Unscrew the hinge bolt on the inside of the door in the
area c/6.
Caution: Support the door.
3.
Take off the refrigerator door.
4.
Take out the fi xing screws and remove the upper bracket
6. Note the small plastic plate underneath the bracket.
5.
Turn the bracket 6 including the small plastic plate through
180° and replace it on the other side of the refrigerator,
using the two screw holes adjacent to each other.
6.
Remove the hinge support 5 from the underside of the
door and fi t the hinge support provided on the opposite
side.
7.
Take out the covering caps and then remove the hinge
support in the middle 4.
Caution: Support the door.
8.
Take off the freezer door 3.
9.
Remove the lower panel 1.
10. Take out the fi xing screws and remove the bracket 2 with
its hinge bolt.
11. Unscrew the hinge bolt, together with the washers, from
the bracket, and fi t it into the corresponding opening on
the opposite side of the bracket.
12. Remove the bracket 7 and replace it with the holding
bracket 2 with its hinge bolt.
13. Now install the holding bracket 7 in the previous position
of the bracket 2.
14. Take out the sealing plugs 8 from the partition separating
the refrigeration and freezer compartments and replace
them in the openings on the opposite side.
15. Take out sealing plug 9 from the freezer door and replace
it in the opening on the opposite side.
16. Place the freezer door onto the hinge bolt on holding
bracket 2.
Caution: Support the door.
17. Turn the holding bracket 4 with its hinge bolt through 180°,
ensuring that the washers remain in place.
18. Replace the bracket on the opposite side on the freezer
door and secure it with the screws.
19. Replace the covering caps over the screw heads.
20. Place the refrigerator door onto the hinge bolt on holding
bracket 4.
Caution: Support the door.
21. Re-insert the hinge bolt of the bracket 6 into the
refrigerator door.
22. Fit the four covers c over the bracket and the openings.
23. Remove the screw covering caps a and the sealing plugs
b.
24. Take out the screws holding the door handles. Move the
handle slightly towards the side with the screw and then
pull the handle off to the front.
25. Fit the handles on the opposite side, using the fi xing
screws to secure them. Push the sealing plugs into the
now empty openings in the door and replace the covering
caps on the screw heads.
26. Take out the cover 10 from the lower panel 1 and replace
it on the opposite side.
27. Replace the panel 1 on the appliance.
15
Tabla de contenido
loading

Tabla de contenido