Idiomas disponibles
Idiomas disponibles
FEMALE MASONS MITRE
Angle = 90º
Width = 600/610/616/620/635/700/
900*/950*mm (*KWJ950/PRO only)
Inset = 3mm or 10mm
• Choose 3mm or 10mm inset (Fig. F7a). If using radius
worktop and 10mm inset, check radius is ≤ 8mm (Fig.
F7b). 3mm inset is recommended for square-edge
worktop only.
• Insert two pins into the Front Edge Alignment Device
Pin Holes (Fig. F8a) and through the corresponding
holes on the Front Edge Alignment Device.
• Insert one pin into the corresponding Female Backset
Pin Hole, according to worktop width and inset (Fig.
F8b).
• Insert F3 or F10 T-gauge into the joint slot (Fig. F8c),
ensuring that the arrow is facing the worktop as
indicated on the T-gauge.
• Position the jig over the female worktop, ensuring
that the Front Edge Alignment Device, T-Gauge and
backset pin are pushed against the worktop.
• Clamp the jig to the worktop (Fig. F10).
• Remove the T-gauge and Front Edge Alignment
Device, ensuring that the jig is not accidently moved
(Fig. F11).
• Complete roughing cuts. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. F5).
• Complete finishing cut. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. F6).
FEMALE MASONS MITRE
Angle ≠ 90º or
Width ≠ 600/610/616/620/635/700/
900*/950*mm (*KWJ950/PRO only)
• Scribe and cut male and female worktop lengths (Fig.
F12). Leave the male oversized.
• Overlay/Underlay the male and female worktop lengths
(Fig. F13a/F13b).
• Using a square, mark the front edge of the female
worktop with a pencil (Fig. F14a/F14b).
• Choose your desired female inset - 3mm, 10mm or
35mm (Fig. F15a). If using radius worktop and 10mm
inset, check radius is ≤ 8mm (Fig. F15b). 3mm inset
is recommended for square-edge worktop only.
• Insert two pins into the Front Edge Alignment Device
Pin Holes (Fig. F16a) and through the corresponding
holes on the Front Edge Alignment Device.
• For 3mm and 10mm inset, insert F3 or F10 T-gauge
into the joint slot (Fig. F16b). For 35mm inset, insert
pin into Female Inset Pin Hole "F35" (Fig. F16c).
• Position the jig over the female worktop and accurately
EN - KWJ700/950/PRO
align the Front Edge Alignment Device to the pencil
mark on the female worktop (Fig. F17), ensuring that
the Front Edge Alignment Device and T-gauge are
pushed against the worktop.
• Clamp the jig in place (Fig. F18).
• Remove the T-gauge and Front Edge Alignment
Device, ensuring that the jig is not accidently moved
(Fig. F19).
• Complete roughing cuts. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. F5).
• Complete finishing cut. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. F6).
MALE MASONS MITRE
Angle = 90º
• Insert two pins into Male Pin Holes "M" (Fig. M1)
ensuring that the inset is equal to the inset used for the
female cut.
• Align the location pins to the postform edge of the
worktop (Fig. M2)
• Clamp the jig to the worktop (Fig. M3)
• Complete roughing cuts. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. M4).
• Complete finishing cut. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. M5).
MALE MASONS MITRE
Angle ≠ 90º
• Overlay (RH) or underlay (LH) the male worktop length,
and mark the female cut line on the male with a sharp
pencil (Fig. M6a/M6b).
• Insert the short and long male positioning devices into
the joint slot (Fig. M7). Ensure that the cut lines are
positioned as shown. (Fig. M8).
• Align the male positioning devices to the pencil line.
• Clamp the jig in place (Fig. M9).
• Remove male positioning devices A and B, ensuring
that the jig is not accidently moved (Fig. M10).
• Complete roughing cuts. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. M4).
• Complete finishing cut. Ensure guide bush is pushed
against the outside edge of joint slot as indicated by
router direction arrow (Fig. M5).
CONNECTING BOLT RECESSES
• The backset position for the connecting bolts is
125mm from the back of the worktop (Fig. B1a).
To use the backset position, insert a pin into the
-22-
