Idiomas disponibles
Idiomas disponibles
Isolatethe range fromthegassupplypipingsystemby
closingits individual manual s hutoff v alveduringany
pressure testingof thegassupply pipingsystem attest
pressures equaltoor lessthan1/2psig(3.5kPaor 14"
watercolumn).
LP/Propane
Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
If you wish to convert your range for use with LP/
Propane gas, use the supplied fixed orifices located
in a bag containing the literature marked "FOR
LP/PROPANE
GAS CONVERSION".
Follow the
instructions
packaged with the orifices for surface,
oven and broil burners conversion.
The conversion must be performed by a qualified
service technician
in accordance with the
manufacturer's
instructions
and all local codes and
requirements.
Failure to follow these instructions
could result in serious injury or property damage.
The qualified agency performing this work assumes
responsibility
for the conversion.
Failure to make the appropriate
conversion
can result in serious personal injury and
property damage.
|
Moving the Appliance
for
Servicing
and Cleaning
Turn off the range line fuse or circuit breakers at
the main power source, and turn off the manual gas
shut-off valve. Make sure the range is cold. Remove
the service drawer (warmer drawer on some models)
and open the oven door. Lift the range at the front
and slide it out of the cut-out opening without creating
undue strain on the flexible gas conduit. Make sure
not to pinch the flexible gas conduit at the back of the
range when replacing the unit into the cut-out opening.
Replace the drawer, close the door and switch on the
electrical power and gas to the range.
|
Range
Installation
Important Note: Door removal is not a requirement for
installation
of the range, but is an added convenience.
Refer to the Use
and Care Guide for
oven door removal
instructions.
Figure 11 dj
:/
1//
E_[_fhe
range cooktop overlaps the countertop
at
the sides and the range rests on the floor. The
cooktop is 31 1/2" (80 cm) wide.
_lnstall
base cabinets 30" (76,2 cm) apart. Make
sure they are plumb and level before attaching
cooktop. Shave raised countertop edge to clear
31 1/2" (80 cm) wide range top rim.
_Jlnstall
cabinet doors 31" (78,7 cm) min. apart so it
will not interfere with range door opening.
_J_Cutout
countertop exactly as shown on page 1.
For models
equipped
with
LevelincL
Device:
_Make
sure the front leveling legs and the rear
leveling device are setup higher than the height of
the cabinet.
Install the anti-tip bracket at this
point before placing the range at its final position.
Follow the installation
instructions on page 15 or
on the anti-tip bracket template supplied with the
range.
E_[_To
provide an optimum installation, the top
surface of the countertop
must be level and
flat (lie on the same plane) around the 3 sides
that are adjacent to range cooktop. Proper
adjustments
to make the top flat should be made
or gaps between the countertop
and the range
cooktop may occur.
To reduce the risk of damaging your
appliance, do not handle or manipulate it by the
cooktop or control console. Manipulate with care.
_'lPosition
range in front of the cabinet opening.
|Make
sure that the cooktop which overhangs the
countertop clears the countertop.
If necessary,
raise the unit by lowering the leveling legs.
|Slide
the range into the cutout opening and
center it before leveling it.
_l_"lLevel
the range (see section 11). The floor where
the range is to be installed must be level. Follow
the instructions
under "Leveling the Range-
Models Equipped with Leveling Device".
E_Adjust
leveling legs so that the underside of the
cooktop is sitting on the countertop.
Carefully
screw in (refer to Leveling the range: Models
equipped with Leveling Device") the back leveling
leg until the cooktop overhang touches slightly the
countertop. Then carefully screw in the front two
leveling legs until the cooktop overhang touches
slightly the countertop.
11
