Idiomas disponibles
Idiomas disponibles
English
SPECIFICATIONS
1. Power tool
Model
Voltage
No-load speed
Blade size (Trimming width)
Battery available for this tool*
Weight**
Continuous operating time (depending
on the work conditions)
*
Existing batteries (BSL3660/3620/3626, BSL18xx series, etc.) cannot be used with this tool.
** According to EPTA-Procedure 01/2014
2. Battery
Model
Voltage
36 V / 18 V (Automatic Switching*)
Battery capacity
Available cordless
products**
Available charger
*
The tool itself will automatically switch over.
** Please see our general catalogue for details.
3. Charger
Model
Charging voltage
Weight
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YSL3>
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red. (See Table 1)
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3 (on page 2).
3. Charging
When inserting a battery in the charger, charging will
commence and the charge indicator lamp will blink in
blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
4.2 kg (With BSL36A18X attached)
4.5 kg (With BSL36B18X attached)
BSL36A18X
2.5 Ah / 5.0 Ah
(Automatic Switching*)
Multi volt series, 18V product
Sliding charger for lithium ion
batteries
UC18YSL3
14.4 V – 18 V
0.6 kg
CH3656DA
1000 – 1500 min
560 mm
Multi volt battery
Approx. 62.5 minutes
Table 1: Indications of the charge indicator lamp
ON/OFF at 0.5 sec. intervals
(RED)
Lights for 0.5 sec. at intervals of
1 sec. (BLUE)
Lights for 1 sec. at intervals of
0.5 sec. (BLUE)
Lights continuously (BLUE)
Lights continuously (Continuous
buzzer sound: about 6 sec.)
(GREEN)
ON/OFF at 0.3 sec. intervals
(RED)
ON/OFF at 0.1 sec. intervals
(Intermittent buzzer sound:
about 2 sec.) (PURPLE)
NOTE
*1 If the red lamp continues to blink even after the charger
has been attached, check to confi rm that the battery has
been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery has cooled
down even when left in situ, the best practice is to
remove the battery and allow it to cool down in a shaded,
well-ventilated location before charging.
*3 Malfunction in the battery or the charger
–
Fully insert the battery.
–
Check to confi rm that no foreign matter is stuck to
the battery mount or terminals. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
10
CH3672DA
36 V
-1
720 mm
4.4 kg (With BSL36A18X attached)
4.6 kg (With BSL36B18X attached)
Approx. 48 minutes
Before charging *
Charged at less than
50%
Charged at less than
80%
Charged at more than
80%
Charging complete
Overheat standby *
Charging impossible *
1
2
3
