Idiomas disponibles
Idiomas disponibles
EN
3.
Insert the Parallel Guide into the Parallel Guide Mounting
Slots (23) and adjust to the required distance (Fig. VII)
4.
Tighten the Parallel Guide Adjustment Screws
5.
Do a test on a scrap workpiece to check the distance
Accessories
•
A full range of accessories including blades, is available from
your Silverline stockist
•
Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: Always disconnect the tool from the power supply, before
cleaning or carrying out maintenance.
General inspection
•
Regularly check that all the fixing screws are tight. They may
vibrate loose over time
•
Inspect the supply cord of the tool, prior to each use, for
damage or wear. Repairs should be carried out by an
authorised Silverline service centre. This advice also applies
to extension cords used with this tool
Lubrication
•
Lubricate all moving parts with a suitable lubricant spray, at
regular intervals
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection
and gloves when cleaning this tool.
•
Keep your tool clean at all times. Dirt and dust will cause
internal parts to wear quickly, and shorten the device's
service life
•
Clean the body of your tool with a soft brush, or dry cloth
•
Never use caustic agents to clean plastic parts. If dry
cleaning is not sufficient, a mild detergent on a damp cloth
is recommended
•
Water must never come into contact with the tool
•
Ensure the tool is thoroughly dry before using it
•
If available, use clean, dry, compressed air to blow through
the ventilation holes (where applicable)
Brushes
•
Over time the carbon brushes inside the motor may
become worn
•
Excessively worn brushes may cause loss of power,
intermittent failure, or visible sparking
•
If you suspect that the brushes may be worn, have them
replaced at an authorised service centre
Contact
For technical or repair service advice, please contact the helpline on
(+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
UK Address: Toolstream Ltd. Boundary Way, Lufton Trading Estate,
Yeovil, Somerset, BA22 8HZ, United Kingdom
EU Address: Toolstream B.V. De Keten, 00004, 5651 GJ, Eindhoven,
Netherlands
Storage
•
Store this tool carefully in a secure, dry place out of the
reach of children
•
For long-term storage, remove batteries and store
separately
Disposal
Li-ion batteries should not be disposed of with household waste. If you do
not know of a li-ion battery recycling centre in your area, contact your local
authority or original dealer for advice on disposal of li-ion batteries.
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
•
Do not dispose of power tools, batteries or other waste
electrical and electronic equipment (WEEE), with household
waste
•
Contact your local waste disposal authority for information
on the correct way to dispose of power tools and batteries
Troubleshooting
Problem
Possible Cause
Battery not fully
Red LED (27) does
Battery Charger (24)
not illuminate and
not powered
Battery (6) not
charging
Battery not being
Battery has low
fully charged
capacity
Battery has been
ON/OF Trigger
charged over 300
Switch (3) not
times and capacity
working
has started to
Trigger Lock (2)
Jigsaw does not
start when ON/OFF
Trigger Switch is
Battery completely
pressed
Disc is off
Defective Battery
centre/vibrating
eccentrically
Jigsaw defective
Internal damage or
Excessive noise or
rattling
Incorrectly fitted
Applying to much
Blade misaligned
Blade blunt or
Overheating
Incorrect blade
Blocked motor
housing vents
silverlinetools.com
Original Instructions
Solution
Check the contact
areas of the battery
and charger are
clear, and the
seated
electrical contacts
are clean and not
damaged
Check mains
connection
Charge the Battery
until Red LED is
extinguished
This is normal for
batteries. Contact
your Silverline
dealer to purchase a
replacement
reduce
battery
Press the Trigger
Lock to disengaged
before operating
engaged
the ON/OFF Trigger
switch
No battery
Attach a battery to
connected
the tool
Recharge Battery or
replace with a fully
discharged
charged battery
Replace Battery
Contact your
Silverline dealer or
authorised service
centre
Contact your
wear
Silverline dealer or
authorised service
centre
Check blade is
blade
inserted correctly
Allow tool to work
force
at its own rate
Check blade is
inserted correctly
Keep blades sharp
damaged
or replace as
needed
Check the blade is
the correct type for
the material to be
cut
Clear vents e.g.
using compressed
air
12
