Idiomas disponibles
Idiomas disponibles
[rAir] REGULATION OF THE FAN
This menu allows you adjust the power of the heating fan.
There are seven power levels above the default power level setting and seven levels below the default power level setting.
To access the function `rAir´ long press the
`0´. Press the
(P3) button again and the `0´ will flash. With the
or slower than the default power level setting.
[oroL] CLOCK
This function allows you to set the date and the time. This setting is required in order to design schedules for turning the heater on and off.
Once you see the following menu displayed on the screen, proceed as follows:
Press the
(P3) button and the screen will immediately show the following:
Press the
(P3) button again and the hours will begin to flash. If you continue to press this button, the minutes or days of the week can be
adjusted. When the hours, minutes, or days of the week are flasing, use the
To exit this function, press
(P1) button or wait a few seconds. If you push this button before selecting and confirming, the information will
not be saved.
ABOUT REMOTE CONTROL
It is possible to choose 6 combinations for the remote control signal at different frequencies.
1.
We start by pressing two buttons on the remote control for more than 10 seconds: we keep pressing these two buttons that can be combinations (on
+), (on -), (on off), (+ -), (+ off) o (off -).
2.
Then the upper red LED starts flashing rapidly (100 ms on and 100 ms off).
3.
After 10 seconds, the led remains on.
4.
To confirm the change, release the buttons after 5 seconds. If the buttons are not released within 5 seconds the LED goes off and the frequency
change is not made.
5.
Then turn off the power to the appliance, and reconnect it after about 10 seconds. When you reconnect the power to the appliance, keep any button
on the remote control pressed until you hear a "beep
6. MAINTENANCE AND CLEANING
It is necessary to carry out certain maintenance tasks in order to keep the heater functioning properly. The frequency of these maintenance tasks will depend largely on the hours of operation and
the quality of the fuel that is being burned. Some of these maintenance tasks must be carried out daily and others can be carried out on a seasonal basis.
A table of the tasks that require carrying out is shown below:
Cleaning the brazier, cleaning the holes in the brazier, and removing ashes
Removal of ashes from the burner
Use of the scrapers
Empty ashtray and vacuum the grate and housing
Clean the inspection "T"
Internal cleaning of the combustion chamber (depending on fuel quality)
Door cord decompression
Extraordinary cleaning
(P3) and
(P4) buttons until `rAir´, inmmediately after this, press the
(P2) or
(P4) buttons, select the desired power for the fan, either faster
[Cron] PROGRAMMING SCHEDULES
This function allows on/off times to be set for the heater.
This function has two sections, one to choose the scheduling mode that you wish to activate (ModE), and the other for programming the schedules
for each one of the modes (ProG). In order to access this function, long press the
display (D1), then press the
(P2) button and `Cron´ will appear, meaning that this function has now been accessed. Now, immediately press the
(P3) button, enter into the programming mode that was mentioned previously (ModE) or (ProG), which can be navigated with the
(P4) button and then selected with
(P2) or
[tELE] REMOTE CONTROL
This function is used to activate and deactivate the remote-control functionality.
This menu is disabled by factory default (OFF). In order to enable remote control functionality, it is necessary to activate this function (ON).
The procedure is as follows:
Go to the [tELE] function and press the
CHORES
(P3) button and figure
(P3) button. (
Download full manual with QR code to view the complete programming process)
(P4) buttons to adjust these values.
(P3) button, as shown below.
31
31
(P3) and
(P4) buttons. `rAir´ will appear on the upper
(P2) or
EN
