Idiomas disponibles
Idiomas disponibles
EN
6. How do I set the tension of the timing belts?
Timing belts on the left and right plates
( 1) Loosen screw 1 and then turn screw 2 to set the tension.
(2) Turn screw 2 clockwise to tighten the belt, and turn it counterclockwise to
loosen it.
(3) Make sure that you set the timing belts on the left and right plates with the
same tension.
(4) After setting the tension, tighten screw 1.
1
2
2
Tighten
Loosen
Timing belt on the middle plate
( 1) Loosen screw 1.
(2) Turn screw 2 clockwise to tighten the belt, and turn it counterclockwise to
loosen it.
(3) After setting the tension, tighten screw 1.
1
7. A pattern engraved on a material is deformed, why?
Possible cause:
The timing belts are set too tight.
Solution:
Check the timing belts on the middle, left, and right plates. Hold the upper and
lower parts of a belt with your fingers to feel the tension. If it is too loose or tight,
set its tension by turning the screws. For details, see FAQ 6 "How do I set the
tension of the timing belts?"
8. The red-cross light beams are not under the
center of the laser module, why?
There is a spacing of 16 mm between the red cross light beams and the laser
light-emitting point. The red-cross light beams are used for framing. When
starting to work, the laser module moves 16 mm to the left along the middle
plate.
The red-cross light beams are not straight due to the refraction of the light shield.
This doesn't affect the performance of engraving.
3
9. After I configure the Wi-Fi connection, the
machine can't be automatically connected to the
software when I open the software again, why?
Possible causes:
The IP address of Wi-Fi network has changed. The IP address used when you
restart the machine is not the same as the one you used when configuring the
Wi-Fi network.
xTool D1 connects to the Wi-Fi network according to the IP address.
Solution:
■
You can use your mobile phone to set up a hotspot, configure the Wi-Fi
network and restart the software to connect your machine.
■
Set a fixed IP address for the Wi-Fi network.
10. How do I perform regular maintenance on
the machine? How often?
The slide bars are chrome-plated optical shafts. You need to apply lubricant to
them regularly to prevent rust. The following describes the details:
Periods:
Generally, apply grease after you use the machine for 15 days to 2 months:
■
Frequently used, running for more than 8 hours per day. You need to apply
1
grease to it at least once every 15 days.
■
Less frequently used, running no more than 2 hours per day. You need to apply
grease to it at least once every 2 months.
■
If the a slide bar is are dirty or impurities are found. Clean its surface and then
apply grease to it.
Precautions for maintenance:
■
Before maintenance, clean away the dirt and impurities from the surface of
the optical shaft,
■
During maintenance, ensure that the grease is evenly applied, wipe off excess
grease, and ensure that the optical shaft is clean and free of impurities.
■
After maintenance, manually push and pull the sliding blocks on the middle,
left, and right plates to ensure smooth operation without jams.
■
You need to perform regular maintenance on the optical shafts on the middle,
left, and right plates, four in total.
11. Do I need to clean the laser module? If yes,
how often?
The laser module needs to be cleaned when the light shield is dirty or when the
laser beams can't cut through materials.
■
Disconnect the machine from the power supply and remove the laser module
Tighten
from the machine.
2
■
Clean the inner and outer frames of the shield with tissues or dust-free cloth
Loosen
moistened with alcohol.
■
Clean the laser lens and infrared laser-emitting point with a cotton swab
moistened with alcohol.
For more details, watch the video at:
youtu.be/lh53_cg6tW0
12. Other problems
If you can't solve your problems, you can contact us for after-sales services at
[email protected]. Please include a fault video, machine firmware version, and
machine SN in the email.
DECLARATION OF CONFORMITY
Hereby, Makeblock Co., Ltd. declares that this product is in compliance
with the essential requirements and other relevant provisions of
Directive RED 2014/53/EU and the RoHS directive 2011/65/EU & (EU) 2015/863.
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and your body.
Statement
■
Thank you for choosing the xTool products!
■
If you use the product for the first time, read carefully all the
accompanying materials of the product to improve your experience
with it. If you do not use the product according to the instructions
and requirements of the Manual, or mis-operate the product due to
misunderstanding, etc., Makeblock Co., Ltd. shall bear no responsibili-
ty for any loss resulting therefrom, except for losses caused due to
improper installation or operation by Makeblock professional
maintenance personnel.
■
Makeblock Co., Ltd. has collated the content of the Manual
rigorously and carefully, but errors or omissions may remain.
■
Makeblock Co., Ltd. is committed to continuously improving
product functions and service quality, and therefore reserves the right
to change any product or software described in the Manual and the
content of the Manual at any time without prior notice.
■
The Manual is intended to help you use the product properly and
does not include any description of hardware and software
configuration. For product configuration, refer to the related contract
(if any) and packing list, or consult your distributor. Images in the
Manual are for reference only and the actual product may vary.
■
Protected by copyright laws and regulations, the Manual shall not
be reproduced or transcribed in any way, or be transmitted on any
wired or wireless network in any manner, or be translated into any
language without the prior written authorization of Makeblock Co.,
Ltd..
EN
4
