Idiomas disponibles
Idiomas disponibles
Work with moderate feed, adapted to the material being cut.
Do not reduce the speed of running down cutting discs by applying
sideward pressure.
The direction in which the cutting is performed is important.
The tool must always work in an up-grinding motion.
Therefore, never move the tool in the other direction! Otherwise, the
danger exists of it being pushed uncontrolled out of the cut.
10. OVERLOAD
Overloading will cause damage to the motor of your angle grinder.
This can happen if your angle grinder is subjected to heavy use for
prolonged periods of time.
Never attempt to exert too much pressure on your angle grinder to
speed up your work.
The abrasive discs operate more efficiently when light pressure is
exerted, thus avoiding a drop in the speed of your angle grinder.
If your angle grinder becomes too hot, run it no load for 2-3 minutes
until it has cooled to normal operation temperature.
WORKING HINTS FOR YOUR ANGLE GRINDER
1. Always start at no load to achieve maximum speed then start
working.
2. Do not force the disc to work faster, reducing the Disc's moving
speed means longer working time.
3. Always work with a 15-30 angle between disc and workpiece.
Larger angles will cut ridges into the workpiece and affect the
surface finish. Move the angle grinder across and back and forth
over the workpiece.
4. When using a cutting disc never change the cutting angle
otherwise you will stall the disc and angle grinder motor or break
the disc. When cutting, only cut in the opposite direction to the disc
rotation. If you cut in the same direction as the disc rotation the
disc may push itself out of the cut slot.
5. When cutting very hard material best results can be achieved
with a diamond disc.
6. When using a diamond disc it will become very hot. If this
happens you will see a full ring of sparks around the rotating
disc. Stop cutting and allow to cool at no load speed for 2-3
minutes.
7. Always ensure the workpiece is firmly held or clamped to prevent
movement.
MAINTENANCE
Remove the battery before carrying out any adjustment,
servicing or maintenance.
There are no user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry place. Keep the
motor ventilation slots clean. Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation slots. This
is normal and will not damage your power tool.
For Battery tools
The ambient temperature range for the use and storage of tool and
battery is 0
C-45
C.
o
o
The recommended ambient temperature range for the charging
system during charging is 0
C-40
o
EN
C.
o
ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authorities or retailer for recycling advice.
TROUBLESHOOTING
Although your new angle grinder is really very simple to operate, if
you do experience problems, please check the following:
1. If your grinder wheel wobbles or vibrates, check that outer
flange is tight; check that the wheel is correctly located on
the flange plate.
2. If there is any evidence that the wheel is damaged do not
use as the damaged wheel may disintegrate, remove it and
replace with a new wheel. Dispose of old wheels sensibly.
3. If working on aluminum or a similar soft alloy, the wheel will
soon become clogged and will not grind effectively.
PLUG REPLACEMENT (ONLY FOR
REWIRABLE PLUG OF UK & IRELAND)
If you need to replace the fitted plug then follow the instructions
below.
IMPORTANT
The wires in the mains lead are colored in accordance with the
following code:
Blue = Neutral
Brown = Live
As the colors of the wires in the mains lead of this appliance
may not correspond with the colored markings identifying the
terminals in your plug, proceed as follows. The wire which is
colored blue must be connected to the terminal which is marked
with N. The wire which is colored brown must be connected to the
terminal which is marked with L.
WARNING!
Never connect live or neutral wires to the earth terminal of the
plug. Only fit an approved BS1363/A plug and the correct rated
rated current fuse which is used in the plug.
Note: If a moulded plug is fitted and has to be removed take
great care in disposing of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
Connect
Blue to N
(neutral)
Outer sleeve
clamped
Fuse
Brown L(live)
Cable grip
13
