Tabla de contenido
Idiomas disponibles
Idiomas disponibles
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES
MANUAL CAREFULLY BEFORE INSTALLING, USING,
OR SERVICING THE MACHINE, PAYING SPECIAL
ATTENTION TO SAFETY RULES. CONTACT YOUR
DISTRIBUTOR IF YOU DO NOT FULLY UNDERSTAND
THESE INSTRUCTIONS.
This machine must be used for cutting only.
It is also essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must
be stored carefully in a pica familiar to everyone involved in
using the machine. They must be consulted whenever
doubts arise and be kept for the entire lifespan of the
machine; they will also be used for ordering replacement
parts.
1 INSTALLATION
1.1 DESCRIPTION OF DEVICES ON THE MACHINE
A)
Block LED; lights when hazardous conditions
arise (See 5.3)
B)
Mains power LED.
C)
Thermostat LED.
D)
Low air pressure LED.
E)
Push-button to activate and deactivate the "SELF-
RESTART PILOT" function.
F)
"SELF-RESTART PILOT" function LED.
G)
Grounding clamp.
H)
Cutting current regulator knob.
I)
Torch fitting.
J)
Pressure regulator knob.
K)
Pressure gauge.
L)
Compressed air fitting (1/4" female gas thread).
M)
Air pressure regulator.
N)
Mains power switch.
O)
Water trap.
P)
Power cord.
1.2 SAFETY DEVICES
This system comes equipped with the following safety
devices:
Overload cut-out:
To avoid overloads. It is evidenced by the C led
continuously on (see pict.1).
Pneumatic:
Located on the torch inlet to prevent low air
pressure. The LED D lights when tripped (see
pict.1).
The blinking D led means t
g
one below 3.2 ÷ 3.5 bar.
Electri
c
al:
1. It signals the presence of dangerous tensions
inside the machine. The LED B (see pict.1) lights
to indicate this function. The LED B keeps on
lighting, even after havin
machine, until dangerous internal tensions persist.
2. Located on the torch body, to prevent hazardous
voltages from occurring on the torch
electrode or nozzle holder are replaced.
To nsure the efficiency of these safety devices:
e
Do not remove or short-circuit the safet
Use only original spare parts.
INSTRUCTIONS FOR PLASMA CUTTER
hat the pressure has temporarily
g switched off the
when, swirl ring,
y devices.
Always replace any da
with original materials.
Do not run the machine without its housings. This
would be dangerous to the operator and anyone else
in the work area, and w
being cooled properly.
1
.3 EXPLANATION OF TECHNICAL SPECIFICATIONS
EN 60974-1
The equipment is built according to these
EN 60974-7
standards.
EN 60
974-10
Cl. A
Machine for pr
Single-phase
frequency converter.
Down slope.
Suitable for plasma cutting.
TORCH
TYPE Type of torch to be used
to form a safe system.
U0
Secondary open-circuit v
X
Duty cycle percentage.
The duty cycle expresses the percentage of
10 minutes during which the welding
machine may run at a certain cu
voltage U
I
Cutting current.
2
U
Secondary
2
welding current I
on the distance bet
the workpiece.
If this distance increases, the cutting
voltage also increas
X% may decrease.
U
Rated supply voltage.
1
1~ 50/60Hz
50- or 60-Hz single-phase power supply
I
Max
Max.
1
corresponding current I
I
eff
This is the maximum value of the actual
1
current
cycle.
IP
23
Protection rating for the housing.
Grade 3 as the second digit means that this
equipmen
the rain.
7
maged parts of the machine
ould prevent the machine from
ofessio
nal and industrial use.
static
transformer-rectifier
with this machine
oltage.
rrent I
without overheating
.
2
conventional
voltage
. This voltage depends
2
ween the contact tip and
es and the duty cycle
absorbed
current
and voltage U
2
absorbed, considering the duty
t is suitable for use outdoors in
and
2
with
at
th
e
2
Tabla de contenido
