Metabo HPT C 10FCH2 Manual De Instrucciones página 10

English
Workpiece
Move
6mm Wing bolt
(Optional accessory)
6. Confi rmation for use of sub fence (B) ...(Standard accessory)
WARNING:
In the case of left bevel cutting, rotate the sub fence (B). Supposing
it is not able to rotate it, It will contact the blade or some part of
the tool, causing in serious injury to operator.
Sub fence (B)
Fence (B)
7. Position adjustment of laser line (Only Model C10FCH2
WARNING:
∗ Make sure before plugging the power plug into the receptacle
that the main body and the laser marker are turned off .
∗ Exercise utmost caution in handling a switch trigger for the
position adjustment of the laser line, as the power plug is
plugged into the receptacle during operation.
If the switch trigger is pulled inadvertently, the saw blade can
rotate and result in unexpected accidents.
∗ Do not remove the laser marker to be used for other purposes.
CAUTION:
Fig. 13
∗ Laser radiation — Do not stare into beam.
∗ Laser radiation on work table. Do not stare into beam.
If your eye is exposed directly to the laser beam, it can be hurt.
∗ Do not dismantle it.
10
Stopper
(Optional accessory)
Holder
(Optional accessory)
6mm Wing nut
(Optional accessory)
Height adjustment bolt 6mm
(Optional accessory)
Fig. 11
Fig. 12
C10FCH2(S))
•
Fig. 14
∗ Do not give strong impact to the laser marker (main body
of tool); otherwise, the position of a laser line can go out of
order, resulting in the damage of the laser marker as well as a
shortened service life.
∗ Keep the laser marker lit only during a cutting operation.
Prolonged lighting of the laser marker can result in a shortened
service life.
∗ Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous
radiation exposure.
NOTE:
∗ Perform cutting by overlapping the ink line with the laser line.
∗ When the ink line and the laser line are overlapped, the strength
and weakness of light will change, resulting in a stable cutting
operation because you can easily discern the conformity of
lines. This ensures the minimum cutting errors.
∗ In outdoor or near-the-window operations, it may become
diffi cult to observe the laser line due to the sunlight. Under
such circumstances, move to a place that is not directly under
the sunlight and engage in the operation.
∗ Do not tug on the cord behind the motor head or hook your fi nger,
wood and the like around it; otherwise, the cord may come off
and the laser marker may not be lit up.
Ink lining can be easily made on this tool to the laser marker. A switch
lights up the laser marker. (Fig. 15)
Depending upon your cutting choice, the laser line can be aligned with
the left side of the cutting width (saw blade) or the ink line on the right
side.
The laser line is adjusted to the width of the saw blade at the time of factory
shipment. Adjust the positions of the saw blade and the laser line taking
the following steps to suit the use of your choice.
Switch
Laser line
Fig. 15
(1) Light up the laser marker and make a groove of about 3/16 in. (5mm)
deep on the workpiece that is about 1-1/2 in. (38mm) in height and 3-1/2
in. (89mm) in width. Hold the grooved workpiece by vise as it is and do
not move it.
Workpiece
Marking
(pre-marked)
Fig. 16
(2) Then insert a 4mm hex. bar wrench in the 12 diameter hole on the side
of the gear case, turn the hex. socket set screw to move the laser line.
(If you turn the Hex. socket screw clockwise, the laser line will shift to
the right and if you turn it counterclockwise, the laser line will shift to the
left.) When you work with the ink line aligned with the left side of the saw
blade, align the laser line with the left end of the groove. (Fig. 17) When
you align it with the right side of the saw blade, align the laser line with
the right side of the groove.
Saw blade
Cutting width