Idiomas disponibles
Idiomas disponibles
2. Check the air pressure in the tyres. If the air
pressure is incorrect, the mower housing will
not cut level. The correct air pressure is:
Front Tyres 0,97 BAR (14 PSI), Rear Tyres
0,69 BAR (10 PSI).
3. If equipped, remove the gauge wheels.
4. (Figure 18) Move the lift lever (1) to the
level adjustment position (2).
WARNING: The lifter lever (1) is
spring loaded. Make sure the lift
lever (1) is locked in the level ad-
justment position (2).
5. (Figure 19) Loosen the left and right ad-
juster knobs (1). Push down on each side of
the mower housing. Make sure both sides of
the mower housing are setting on a flat sur-
face. Also, make sure the lift links (2) are
loose and can easily move up or down
6. Push down on the lift links (2) and tighten
the left and right adjuster knobs (1). If
necessary, use a wrench to tighten the ad-
juster knobs (1)
7. (Figure 18) Raise the lift lever (1).
8. If equipped, attach the gauge wheels.
9. Mow for a short distance. If the height of cut
is not level, repeat the above steps.
Where To Lubricate (Figure 16)
Models with grease fittings:
Lubricate with grease gun.
Apply grease with a brush to
the areas shown.
Lubricate the areas shown
with engine oil.
NOTE: Apply grease to the steering gear as-
sembly.
CAUTION: If the unit is operated in dry areas
that have sand, use a dry graphite spray to
lubricate the unit.
Check The Tyres
Check the air pressure in the tyres. Tyres with too
much air pressure will cause the unit to ride rough.
Also, the wrong air pressure will keep the mower
housing from cutting level. The correct air pres-
sure is: Front Tyres 0,97 BAR (14 PSI), Rear
Tyres 0,69 BAR (10 PSI).
How To Replace The Motion Drive Belt
1. Remove the mower housing. See the instruc-
tions on "How To Remove The Mower Hous-
ing".
2. (Figure 21) Remove the screws (1) that hold
each side of the middle discharge chute
(2). Remove the middle discharge chute
(2).
3. (Figure 20) Disconnect the belt tension
spring (1).
4. (Figure 25) Remove the three idler pulleys
(2).
5. (Figure 20) Remove the adjuster nut (3)
from the idler bracket (4).
6. (Figure 22) Remove the three screws (1)
from the transaxle sheild (2). Place the
transaxle shield (2) in the tunnel (3). The
bag full indicator (4) wire harness will limit
the transaxle sheild (2) movement.
F–010712J
7. (Figure 23) Loosen the belt guide (1) at the
drive pulley (3).
8. Remove the motion drive belt (4) from the
drive pulley (3).
9. (Figure 24) To remove the motion drive belt
(1) from the stack pulley (2), pull the front
end of the belt under the stack pulley (2)
and then back between the stack pulley and
the steering plate (3).
10. Remove the motion drive belt. A correct re-
placement part or assistance is available
from an Authorized Service Centre in your
area.
11. To install the motion drive belt, reverse the
above steps.
12. (Figure 25) Check the routing of the motion
drive belt (1). Make sure the motion drive
belt is installed correctly on the idler pulleys.
How To Replace The Mower Drive Belts
(Figure 15)
1. Remove the mower housing. See the instruc-
tions on "How To Remove The Mower Hous-
ing".
2. Loosen and pull the belt retainer (1) away
from the double idler pulley (2). Remove
the primary mower drive belt (3) from the
double idler pulley (2).
3. Pull the belt retainers (4) away from the
single idler pulley (5). Remove the primary
mower drive belt (3) from the single idler
pulley (5).
4. To release tension on the secondary belt,
remove the spring (8) from the double idler
mount (9).
5. Remove the secondary mower drive belt
(10) from the double idler pulley (2) and
from the right mandrel pulley (11).
6. A correct replacement part or assistance is
available from an Authorized Service Centre
in your area.
7. To install the mower drive belt, reverse the
above steps.
How To Remove The Mower Housing
(Figure 36)
1. Move the blade rotation control (1) to the
DISENGAGE position.
2. Move the lift lever (2) to the level adjust-
ment position.
3. Remove the hair pins and the washers from
the adjuster arms (3). See illustrations "C"
and "D".
4. Remove the hair pins and washers from the
suspension links (4). See illustrations "A"
and "B".
5. Disconnect the extension spring (5) from
the blade control rod (6). See illustration
"E".
6. Disconnect the front hanger (9) from the
axle support. See illustration "F".
NOTE: The hanger rod (11) is made with a
a bend.
7. Remove the mower drive belt (7) from the
stack pulley (8). See illustration "G".
8. Disconnect the middle discharge chute
(10) from the mower housing. See illustration
"H".
9. Pull the mower housing away from the right
side of the unit.
17
10. To install the mower housing, reverse the
above steps.
11. Check belt routing of the primary mower
drive belt (1) and the secondary mower
drive belt (2). See illustration "J".
GB
