Idiomas disponibles
Idiomas disponibles
and T. They are located in the areajust
above the primerbulb.
CARBURETOR PRESETS
When makingadjustments,do not force
the plasticlimitercaps beyondthe
stopsor damage willoccur.
If carburetor presetsare not needed,
proceed to "idle Adjustments."
• Turnboth mixture screws counter-
clockwise until they stop.
• Turn the idle speed screw clockwise
until it stops. Now turn counterctock-
' wise4-1/2turns.
Start motor, let it run for 3 minutes, and
proceed to the adjustment section,tf
engine does not start, refer to trouble-
shooting chart or call 1-800-235-5878.
If engine performance is acceptable at
the preset positions and there is no
chain movement at idle, no further ad-
justment is necessary.
ADJUSTING PROCEDURE
Idle Speed "T"
Allow engine to idle. Adjust speed until
engine runswithoutchain movement or
stalling.
• Turn clockwise to increase engine
speed if engine stalls or dies.
• Turn counterclockwise to decrease
speed.
No further adjustments are necessaryif
chain does not move at idle speed and
if performance is satisfactory.
Low Speed Mixture "L"
Allow engineto idle, Then accelerate
the_.engine and note performance. I f en-
ginehesitates,bogsdown, or smokes
duringacceleration, t urn mixturescrew
clockwise in 1/16-turn increments until
performance!s satisfactory. R epeat this
procedureas necessaryfor properad-
justmenLAfter completing adjustments,
checkfo._ accelerationand chainmove-
ment at_ idle. Reset if necessary.
High Speed Mixture "H"
DO NOT operateengine at fullthrottle
for prolongedperiodswhilemaking ad-
justments.Damage to the enginecan
occur.Make a test cut. Based on per-
formanceof the saw while cutting,ad-
just the highspeed mixturesettingin
1!16-turnincrementsas follows:
• Clockwiseuntilthe saw has good
PDower in the cutwith no hesitation.
o notadjustby soundor speed, but
judgeby howwell the saw performsin
the cut.
• Counterclockwise if the saw has
speed, but dies in the cutor lacks
power in the cut.
After completing adjustments,checkfor
acceleration and chainmovement at
idle. Reset if necessary.
Acceleration Check
Ifthe enginedies or hesitatesinsteadof
accelerating, t urnthe low speed mixture
adjustment counterclockwise until you
havesmoothacceleration withno chain
movementat idle. Recheckand adjust
as necessaryfor acceptableperfor-
mance.
Prepare your unit for storage at the end
of the season or if it will not be used for
30 days or more.
WARNING:
• AUow the engine to cool, and secure
the unit before storing or transporting.
• Store chain saw and fuel in a well
ventilated area wherefuet
vapors
cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
° Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot accidentally
cause injury.
• Store chain saw well out of the reach
of children.
EXTERNAL SURFACES
if yourchain saw is to be storedfor a
pedod oftime, clean itthoroughlybe-
fore storage.Store in a clean dry area.
• Lightly oil externalmetal Surfacesand
guidebar.
• Oil the chainand wrap it in heavypa-
per or cloth,
FUEL S_T.,_M
!;
Under Fu_f_'_l:_gine in the Operating
Section0f_thiS:iitanual, see message
labeled IMPOR'rANT regardingthe use
of gasohol in yourchain saw.
Fuel stabilizeris an acceptable alterna-
tive in minimizing the formation of fuel
gum deposits duringstorage.Add stabi-
lizerto the gasolinein the fuel tankor
fuel storagecontainer.Followthe mix
1R
""
i;
"
