Craftsman 137.212890 Manual De Instrucciones página 5

,
,
,
"DRESS FOR SAFETY:
• Plan ahead to protect your eyes, hands, face and
ears.
• Do not wear loose clothing, gloves, neckties or
jewellery (rings, wrist watches). They can get
caught and draw you into moving parts.
• Wear nonslip footwear.
• Tie back long hair.
• Roll long sleeves above the elbow.
• Noise levels vary widely. To avoid possible
hearing damage, wear ear plugs or muffs when
using the chop saw each time.
• The chop saw can throw foreign objects into your
eyes which can result in permanent eye damage.
Wear safety goggles (not glasses) that comply
with CSA Standards. Regular eyeglasses have
only impact-resistant lenses. They are not safety
glasses.
• Wear a dust mask along with safety goggles
during each operation.
INSPECT YOUR WORKPIECE:
• Make sure there are no nails or foreign objects in
the part of the workpiece to be cut.
,
PLAN YOUR CUT:
• Do not cut freehand. Guide your workpiece
solidly against the fence and table top. Make
sure there is no debris between the workpiece
and its supports.
• Use extra caution with large, small or awkward
workpieces.
• Use extra support (tables, sawhorses, blocks) if
your workpiece is hard to hold down to the table.
Do not use another person as additional support
or to help feed, support or pull the workpiece.
• Do not cut more than one workpiece at a time.
• Do not turn your chop saw ON before clearing
everything except the workpiece and related
support devices off the table.
AVOID ACCIDENTAL STARTING:
Make sure the switch is OFF before plugging the
abrasive chop saw into a power source.
WHEN THE CHOP SAW IS RUNNING
I_l_ WARNING I
DO NOT ALLOW FAMILIARITY GAINED FROM
FREQUENT USE OF YOUR CHOP SAW TO CAUSE
A CARELESS MISTAKE. REMEMBER THAT A
CARELESS FRACTION OF A SECOND IS ENOUGH
TO CAUSE A SEVERE INJURY.
_:__- .............. ! J' III Jill
.
KEEP CHILDREN AWAY:
• Make sure all bystanders are clear of the power
tool before and during use.
• Before using the power tool, test the saw by
turning it on and letting it run for a few seconds. If
it makes an unfamiliar noise or vibrates, stop
immediately. Turn the chop saw OFF and unplug.
Do not restart the tool until the problem has been
corrected.
2. DO NOT FORCE THE TOOL:
• Only cut one piece per cutting operation,
.
BEFORE FREEING JAMMED MATERIAL:
• Release the trigger switch.
• Wait for all moving parts to stop.
• Unplug the chop saw.
,
BEFORE LEAVING THE CHOP SAW:
• Release the trigger switch.
• Unplug the chop saw.
• Make the workshop childproof. Lock the shop.
Disconnect master switches.
I,A WARNING I
A 14 in. (356 ram) wheel is the maximum wheel capacity
of your chop saw. Never use a wheel that is too thick
to allow outer flange to engage with the flats on the
spindle. Larger wheels will come in contact with the
wheel guards, while thicker wheels will prevent the bolt
from securing the wheel on the spindle. Either of these
situations could result in a serious accident and can
cause serious personal injury.
L,_ WARNING J
Do not attempt to cut wood or masonry with this chop
saw. Never cut magnesium or magnesium alloy with
this machine. Failure to comply could result in serious
personal injury.
To prevent the chop saw movement or tipping during
cutting procedure, secure the chop saw in place to a
workbench or work surface that is also secure.
1,_ WARNING I
Always use the vise on the chop saw to prevent
accidents that could result in possible serious personal
injury.
[,A WARNING J
Never stand or have any part of your body in line with
the path of the wheel. Doing so may cause an accident
resulting in possible serious personal injury.
5 .......... I l lll