Specific Safety Rules - Makita 9741 Manual De Instrucciones

ENGLISH
1 Hex wrench
2 Spindle
3 Wheel
4 Hex wrench
5 Output shaft
6 Notch
7 Pin
SPECIFICATIONS
Model
Wheel size (Diameter x Width) ................. 100 x 120 mm
–1
No load speed (min ) ............................................ 3,500
Dimensions (L x W x H) .................. 310 x 185 x 182 mm
Net weight .............................................................. 4.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to sander safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
3. Inspect for and remove foreign matter such as
nails, screws, etc. from the workpiece surface
before operation.
4. Secure the workpiece firmly.
5. Do not wear gloves during operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Never attempt to use with the tool held upside
down in a vise, etc.
10. Some material contains chemicals which may be
toxic. Take caution to prevent working dust inha-
lation and skin contact. Follow material supplier
safety data.
Explanation of general view
8 Wing nut
9 Front roller
10 Cover plate
11 Dust port
12 Joint
13 Switch trigger
14 Lock button
11. Use of this tool to sand some products, paints
9741
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Removing or installing wheel (Fig. 1 & 2)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the wheel.
To remove the wheel, insert one hex wrench into the end
of the spindle and another hex wrench into the end of the
output shaft. Turn the hex wrench in the output shaft
clockwise while securely holding the hex wrench in the
spindle so that the wheel cannot revolve. Pull the output
shaft out of the wheel. Move the wheel slightly away from
the spindle and remove the wheel from the tool.
GEB022-1
NOTE:
The output shaft has a left hand thread.
To install the wheel, follow the removal procedures in
reverse. When installing it, be sure to align the notches in
the wheel with the pins on the spindle.
Adjusting front roller (Fig. 3)
The front roller allows you to apply uniform pressure to
the workpiece. To adjust the front roller, set the tool on a
flat surface and loosen the wing nut. Adjust the front
roller up or down until the clearance distance (D) is about
2 mm. Tighten the wing nut securely.
Connecting to dust collector (Fig. 4)
The use of a dust collector makes sanding operations
clean and dust collection easy. To connect a dust collec-
tor, open the dust port by sliding the cover plate up and in
a clockwise direction. Attach the joint onto the dust port.
Now a dust collector can be connected to this tool.
CAUTION:
When not using a dust collector, close the dust port
opening with the cover plate.
15 Grip
16 Handle
17 Limit mark
18 Screwdriver
19 Brush holder cap
and wood could expose user to dust containing
hazardous substances. Use appropriate respira-
tory protection.
3