Idiomas disponibles
Idiomas disponibles
Models: 2271 • 2272
Body (1 piece)
1
Regulator (1 piece)
4
AsseMBlY INsTRUCTIoNs
Find a large, clean area to assemble your appliance�
Remove all packing material before assembling�
Sharp edges. Wear gloves while assembling.
Place the griddle body on a smooth flat surface and screw
STEP 01
the four (4) griddle feet into the bottom of the griddle�
BLACKSTONEPRODUCTS.COM/SUPPORT
Griddle top (1 piece)
2
Grease cup
5
TOOLS NEEDED:
(1 piece)
Phillips head screwdriver &
Adjustable wrench
CAUTIoN
NOT INCLUDED:
lPG cylinder
size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
lPG cylinder must include collar to
lPG cylinder must include collar to
protect lPG cylinder valve.
protect lPG cylinder valve.
NOT INCLUDED:
17" griddle base
Hard cover (1 piece)
3
CLEANING THE BURNER ASSEMBLY
To reduce chance of "flash-back" the procedure below should be
followed at least once a month when spiders are most active or
when your appliance has not been used for a period of time�
Hard cover
Carry bag
6
7
VIDEO TUTORIAL
handle (1 piece)
TOOL NEEDED:
(1 piece)
How to Clean Your Burner Tube
Phillips head screwdriver
youtube.com/watch?v=xKQTCrFCzf8
ensure that the gas is turned oFF at control knobs and gas
STEP 01
supply� Remove the griddle top�
Carefully detach and
STEP 02
remove the burner�
Clean the inside of
STEP 03
the burner:
• Run a narrow bottle brush
through each burner tube
several times� (do NoT use
wire brushes)
NOT INCLUDED:
• Run a stiff wire bent into a small
lPG cylinder
hook through each burner tube
size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)
size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)
several times�
• Use compressed air to blow
through the burner tube and
out the burner ports� Check that
air blows through each hole�
set the griddle on its feet� ensure that the ignition needles
STEP 02
(Wear eye protection)
are set 3-7mm above the burner tubes�
ensure that the fuel nozzles are seated in the burner openings�
Brush entire
STEP 04
outer surface of burner to
remove grime�
Clean any blocked ports
STEP 05
with stiff wire such as an open
paper clip�
NOT INCLUDED:
22" griddle base
Carefully replace
STEP 06
burners and reattach, with
attention to the location of the
ignition needle�
3-7mm
3-7mm
ASSEMBLY GUIDE
| OWNER'S MANUAL
Griddle feet
8
TOOL NEEDED:
(4 pieces)
Adjustable wrench
TOOLS NEEDED:
NOT INCLUDED:
Phillips head screwdriver &
AA battery
Adjustable wrench
NOT INCLUDED:
ELECTRIC REQUIREMENTS:
lPG cylinder
120V 60Hz
Fuel nozzle
Fuel nozzle
size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)
lPG cylinder must include collar to
lPG cylinder must include collar to
protect lPG cylinder valve.
protect lPG cylinder valve.
Burner opening
Burner opening
The gas rail fuel nozzle
must be reengaged within the
burner opening�
CU
Visi
for a
you
CUS
TOO
5mm
TOOL N
NOT
Phillip
AAA
NOT IN
lPG cy
size: 4
size: 4
05
