Idiomas disponibles
Idiomas disponibles
8. Cleaning, maintenance and order-
ing of spare parts
Danger!
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with
compressed air at low pressure.
We recommend that you clean the device immedi-
ately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents or
solvents; these could attack the plastic parts of the
equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool
increases the risk of an electric shock.
8.1.1 Disconnecting and cleaning the gun
Unplug the spray gun from the mains power. Press
the trigger (4), so that the residual ma- terial flows
back into the container (9).
Unscrew the container (9) and empty the residual
material back into the material tin.
Clean the container (9) and the material tube (10)
with a bristle brush.
Pour solvent or water into the container. Screw the
container back on. Solvents with a flash point above
55°C may not be used.
Reinsert the mains plug into the mains outlet and
turn on the paint spray gun. Set the max. paint
volume control (5) to the maximum flow setting.
Spray the solvent or water into a con- tainer or rag,
but never into the surroundings.
Repeat the procedure above until the clear solvent
or water exits from the nozzle (1).
Turn the paint spray gun off again and unplug it from
mains power.
Completely empty the container (9). Always keep
the container (9) free of residue and check it for
damage.
Use a rag soaked in solvent or water to clean the
outside of the paint spray gun and the container (9).
Unscrew the air cap retaining ring (3) and remove
the air cap (2). Remove the nozzle.
Clean the air cap retaining ring, air cap and nozzle
with a bristle brush and solvent or water
Remove the filter cap (8) to clean the air inlet filter.
Remove the filter and clean it by blowing out with
air. Replace the filter and screw the filter cap onto
GB
the gun. Do not operate the gun without the filter.
Reinsert the fluid needle. Pull the trigger and insert
the nozzle on the fluid needle. While inserting,
ensure that the pins on the sides of the fluid needle
point up/down and not right/ left. Pull the trigger
while placing the air cap on the nozzle and tightly
fasten the air cap with the air cap retaining ring.
Ensure that the paint spray gun is completely dry
before storing it.
Properly dispose of residual paint and cleaning
agents in accordance with local laws and
regulations. Residual paint and solvents must be
taken to a suitable collection point. If you are not
sure, ask the local council where the nearest
collection point is.
Warning!
Never immerse the paint spray gun in water or other
liquids. The housing may only be cleaned with a
dampened rag.
NOTE: If you use 2-component paint, you must
clean the gun immediately. Otherwise the paint may
dry inside the gun, causing an equipment fault.
8.2 Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician.
Danger!
The carbon brushes should not be replaced by anyone
but a qualified electrician.
8.3 Maintenance
There are no parts inside the equipment which require
additional maintenance.
9. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The
equipment and its accessories are made of various
types of material, such as metal and plastic. Never
place defective equipment in your household refuse.
The equipment should be taken to a suitable collection
center for proper disposal. If you do not know the
whereabouts of such a collection point, you should
ask in your local council offces.
10. Storage
Store the equipment and accessories in a dark and dry
place at above freezing temperature. The ideal storage
temperature is between 5 and 30 °C. Store the electric
tool in its original packaging.
9
