Metabo BS 14.4 LT Manual Original página 11

Original instructions
1. Declaration of Conformity
On our own responsibility, we hereby declare that
these battery-powered drilling screwdrivers and
impact drills, identified by type and serial number
*1), meet all relevant requirements of directives *2)
and standards *3). Technical documents at *4) -
Fig. M.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
cordless drills/screwdrivers and impact drills,
identified by type and serial number *1) on page 3,
fulfill all relevant provisions of following UK
Regulations S.I. 2016/1091, S.I. 2008/1597, S.I.
2012/3032 and Designated Standards *3).
2. Specified Use
The drills and impact drills are suitable for drilling in
metal, wood, plastic and similar materials, and also
for screwdriving and thread tapping.
The impact drills are also suited for drilling in
masonry, brickwork and stone.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
3. General safety instructions
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. Always include these documents when
passing on your power tool.
4. Special Safety Instructions
4.1 Safety instructions for all operations
a) Wear ear protectors. Exposure to noise can
cause hearing loss.
b) Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
c) Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory or fasteners may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
4.2 Safety instructions when using long drill
bits with rotary hammers
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
b) Always start drilling at low speed and with
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage and loss of control,
resulting in personal injury.
4.3 Further Safety instructions
CAUTION Do not stare at operating lamp.
Protect battery packs from water and mois-
ture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from
defective li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention imme-
diately.
If the machine is defective, remove the battery pack
from the machine.
Remove the battery pack from the machine before
any adjustments, conversions or servicing are
performed.
Before fitting the battery pack, make sure that the
machine is switched off.
Keep hands away from the rotating tool!
Remove chips and similar material only with the
machine at a standstill.
ENGLISH en
11