Idiomas disponibles
Idiomas disponibles
PORTABILITY
KIT INSTALLATION
CORD SET
TOOLS
REQUIRED:
7/16",
1/2", 9/16",
and 5/8" sockets
and
ratchets,
block(s)
of wood
(minimum
of 6" tall).
Refer to the parts
list
on page 9.
WHEEL
INSTALLATION
1.
Block up end of generator
opposite
the fuel tank cap to
install wheel
kit.
2.
Slide the axle (item
35) through
the wheel
brackets
on the
carrier,
then through
a wheel
(item
31), with the offset
side
of the wheel
hub against
the wheel
bracket.
3.
Secure the wheel to the axle with the axle cap (item
16),
tapping
the cap onto the axle with a hammer.
4.
Repeat
above
instructions
for the remaining
wheel.
FOOT
INSTALLATION
1. Assemble
the rubber
feet (item
32) to the foot bracket
(item
27) using a 1/4-20 x 1.5" bolt(item
29).
Thread
a 1/4
washer
(item
39) and a 1/4 nyloc
nut (item
13) to the bolt to
secure
the assembly.
Caution:
Do not over
tighten
so
that the foot
material
collapses.
2.
Blocking
up the alternator
side of the generator,
place the
foot bracket
under the carrier
channel.
Thread
a 5/16-18
x
1" bolt (item
36) with a 5/16 washer
(item
34) through
the
mounting
holes and thread
a 5/16 flange
nut (item
15) to
the bolt to secure
the foot bracket
to the carrier.
HANDLE
INSTALLATION
1.
Place
handle
(item
28) over
carrier
tubing
on same
end as
feet,
centering
handle
on the carrier.
2.
Slide 7/16 x 2" bolt (item
30) through
handle
as shown
in
diagram
and secure
with 7/16" nyloc
nut (item
33).
Tighten
until handle
is securely
clamped
to the carrier
tubing.
3.
Apply
aerosol
hairspray
or similar
adhesive
to the handle
(item
28), and then slide the handle
grip (item
44) onto the
handle.
The aerosol
hairspray
will allow for easier
assembly
and will adhere
the grip to the handle.
Your generator
is supplied
with a 25 foot 12 GA SJTW
4-conductor
105°C
power cord
set.
This cord is equipped
with
an L14-20P
twistlock
Plug, on one end, which will plug directly
into the mating
twistlock
receptacle
on the control
panel of your
generator.
The opposite
end comes
equipped
with a special
4
circuit
connector
comprised
of four 5-20R
receptacles.
These
may be used to power
individual
loads.
Make sure
the loads
do not exceed
the 20 amp
rating
of the Power
Cord
Set.
Circuit
breaker
protection
is provided
for on the control
panel of
your generator.
You will notice that the 4-circuit
connector
is color coded
with red and blue dots.
When
several
loads
are powered
at the
same time,
it is best to keep equal loads supplied
to each
separately
colored
half, if possible.
The red half and the blue
half of the connector
are each capable
of sustaining
20 amps of
current
provided
your generator
is capable
of supplying
4800
watts
of power.
Check
nameplate
ratings
for total wattage
capability
of the generator.
20(_ C K PLUG
/
_-/5-20R
RECEPTACLES
NOTE:
When
using
a generator
cover
with
this
portability
kit, the handle
must
be moved
to the downward
position.
®
Engfish
3
