EINHELL Expert TE-TS 1825/1 U Manual De Instrucciones página 34

Anleitung_TE_TS_1825_U_SPK8_- 26.09.12 15:19 Seite 34
GB
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
n
for damage which may have occurred in transit.
The machine has to be set up where it can stand
n
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
n
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
n
freely.
When working with wood that has been
n
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
n
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
n
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18)
Turn the saw upside down and place it on the
n
floor.
Use the hex screws and nuts to fasten the four
n
wide side struts (41) loosely to the saw.
Now screw the four legs (40) loosely to the wide
n
side struts.
Then screw the four narrow side struts (42)
n
loosely to the four legs (40) and mount the
rubber feet (43) on the legs.
Important! The shorter narrow struts (No. 2)
n
34
have to be used on the sides.
Finally, turn the saw together with the base
n
frame upright and tighten all the screws and nuts
(Fig. 18).
Screw the additional legs (A) to the rear legs
n
(40) so that they point towards the rear of the
machine (Fig. 28).
7.2 Table width extension and length extension
7.2.1 Length extension table (Abb. 19/20)
Use the hex screws and nuts to fasten the table
n
length extension (36) loosely to the saw table (1)
Screw the supports (50) loosely onto the saw
n
housing and onto the table length extension.
Align the table length extension level with the
n
saw table (1).
Finally, tighten all screws and nuts.
n
7.2.2 Width extension tables (Abb. 21/22)
Slide the width extension tables by their
n
connecting tubes into the prepared mounts as
far they will go, making sure that the numerical
scale always faces the front of the machine.
Secure the width extension tables in place with
n
the clamping screws (21) underneath.
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
n
so that the screw fits through the hole (44) in the
splitter.
Do not tighten the screw (15) too far – the blade
n
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
n
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
n
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
n
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 3/6/7/8)
Important! Pull out the power plug.
n
Set the blade (4) to max. cutting depth, move to
n
0° position and lock in place.
Remove the saw blade guard (see 7.3).
n
Take out the table insert (6) (see 7.5).
n
Slacken the fixing screw (20).
n
7.4.1. Setting for maximum cuts (Fig. 6/7/8)
Push up the splitter (5) until the gap between the
n
saw table (1) and the upper edge of the splitter
n
(5) equals approx. 10 cm.