Idiomas disponibles
Idiomas disponibles
WV-CW960_US 05.11.18 11:08 ページ24
2. Move the cursor to →PUSH SET to the right of
PAN/TILT, and then press the CAM (SET) button to
display the PAN/TILT setting menu.
** POSITION 1
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
3. Use the joystick to position the camera, and then
press the CAM (SET) button.
** POSITION 1
PAN/TILT
ZOOM/FOCUS
U TILT D/L PAN R
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
4. Move the cursor to → PUSH SET to the right of
ZOOM/FOCUS, and then press the CAM (SET)
button to display the ZOOM/FOCUS setting menu.
** POSITION 1
PAN/TILT
ZOOM/FOCUS
U ZOOM D/L FOCUS R
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
5. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM (SET) button.
Notes:
• Focusing may be difficult, because of the distortion
caused by the curve of the dome cover, when the
camera is at an angle that is close to horizontal.
• A different position number can be selected by moving
the cursor to the position number at the top of the
position setting menu and tilting the joystick left and
right. Pressing the CAM (SET) button will change to the
setting screen for the newly selected position number.
• The currently registered camera ID and preset ID
appear at the bottom of the position setting menu.
• When using a system device other than the WV-
CU650/CU950*,
position numbers cannot be set. (as of September
2005)
* Operation procedure may vary depending on
the version of the system controller's software.
For Ver.1.xx or earlier: only camera function
operations are supported
For Ver.2.xx or later: PRESET/PGM PRESET
button is also supported
All manuals and user guides at all-guides.com
**
→PUSH SET
→ PUSH SET
→
0
**
→PUSH SET
→PUSH SET
→
0
**
→PUSH SET
→PUSH SET
→
0
WJ-HD309A/HD316A
over
65
Align the cursor here
**
POSITION 1*
PAN/TILT
ZOOM/FOCUS
PAN OFFSET SET ←
RET TOP
FLOOR1
DOOR
● Adjusting Camera Position When
Changing Cameras (PAN OFFSET SET)
The system controller etc. has a function for
downloading (saving) and uploading (recovering)
setting information for the camera. This function allows
you to upload (recover) original setting information that
has
been
downloaded
unforeseen damage or malfunction causes setting
information in the camera to be lost. However, there
may be some slight differences in images from those
uploaded (recovered) when the camera is changed.
The "PAN OFFSET SET" function is for adjusting these
differences.
1. Align the cursor with "PAN OFFSET SET" with the ← or
→ arrow, and press the CAM (SET) button to set the
offset value.
Set the offset value to 0.0, or in a range of -10 to
+10. All preset positions for the camera's position
are adjusted according to the offset value.
Important: Data is not compatible with existing
cameras.
Uploading
existing cameras will damage data in the camera. If
data in the camera is damaged, download camera
setting information from a camera that still has the
factory settings and then upload it to the camera
with the damaged data.
● Preset ID Setting (PRESET ID)
The preset ID is a series of alphanumeric characters
that indicate the location of the camera. This item can
be used to turn display of the preset ID on the monitor
screen on or off, and to input the preset ID.
1. Move the cursor to PRESET ID, and then tilt the
joystick left or right to toggle preset ID display on
and off.
PRESET NO.
POSITION SET
PRESET ID
RET TOP DEL
2. Select ON or OFF, and then press the CAM (SET)
button.
This will display the preset ID setting menu.
-24-
**
→ PUSH SET
→PUSH SET
→
0
(saved)
before
some
setting
information
from
1*
ON
