Installing/Removing Battery Pack; Filling The Tank - Ryobi P2803 Manual Del Operador

Ocultar thumbs Ver también para P2803:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

WARNING:
Do not allow familiarity with the product to make you care-
less. Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields or goggles
marked to comply with ANSI Z87.1. Failure to do so could
result in fluids entering your eyes resulting in possible seri-
ous injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
WARNING:
Use safety equipment. Protect your eyes, skin, and lungs
while mixing, filling, spraying, and cleaning. Failure to do so
may result in serious personal injury and damage to property.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced. Please contact customer service or an authorized
service center for assistance.
APPLICATIONS
You may use this product for the purpose listed below:
 For use with most consumer grade home and garden
chemicals such as insecticides, fungicides, weed killers,
and fertilizers

INSTALLING/REMOVING BATTERY PACK

See Figure 6.
WARNING:
Always remove battery pack from your tool when you are
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental
starting that could cause serious personal injury.
To install:
 Align the raised rib on the battery pack with groove in the
battery port and place the battery pack in the tool.
OPERATION
ASSEMBLY
 Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in the
tool before beginning operation.
To remove:
 Depress the latches on both sides of the battery pack to
release the battery pack and remove it from the tool.
For complete charging instructions, see the operator's manuals
for your battery pack and charger.
Risk of fire or explosion. Spray area must be well-ventilated
and away from sparks or flames.
TURNING THE SPRAYER ON/OFF
See Figures 7 - 8.
 To turn the sprayer ON, depress the ON/OFF button.
 To start the flow of liquid at the spray wand, depress the
trigger.
 To stop the flow of liquid at the spray wand, release the
trigger.
 To turn the sprayer OFF, depress the ON/OFF button again.
LOCK-ON
See Figure 8.
The lock-on feature is convenient when spraying for an extended
period of time or when covering a large area.
 To lock-on, depress the trigger and slide it forward.
 To release the lock-on, depress the trigger and slide it
backward.
NOTE: Make sure the trigger is not locked on before inserting
the battery pack into the sprayer.

FILLING THE TANK

See Figure 9.
Always follow the chemical manufacturer's instructions
printed on their product labeling for use, cleaning, and stor-
age. Clean thoroughly after each use, following the instruc-
tions in the Maintenance section of this manual. Chemicals
should be stored out of the reach of children. Failure to do
so may result in serious personal injury.
Liquids to be sprayed must be as thin as water. Thicker liquids
will not spray properly.
Do not overfill the tank.
 Remove the battery pack.
 Unscrew the measuring cap and remove it from the tank.
 Fill the tank with the desired amount of water (up to 2 gallons).
 Measure the recommended amount of liquid. The measuring
cap may be used for measuring up to 4 oz.
 Carefully pour the liquid into the tank.
7 — English
WARNING:
WARNING:
Tabla de contenido
loading

Tabla de contenido