Ryobi FVB03 Manual Del Operador

OPERATOR'S MANUAL
USB LITHIUM BATTERY PACK
FVB03
To register your RYOBI product,
™
please visit: http://register.ryobitools.com
Use this USB lithium battery pack for RYOBI
products only. Refer to the Operator's Manual provided with product.
Always mention the model number above when communicating
with us regarding this battery pack.
SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
 Battery tools do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition. Be
aware of possible hazards when not using your battery tool
or when changing accessories. Following this rule will reduce
the risk of electric shock, fire, or serious personal injury.
 Do not place battery tools or their batteries near fire or heat.
This will reduce the risk of explosion and possibly injury.
 Do not crush, drop or damage battery pack. Do not use a
battery pack or charger that has been dropped or received a
sharp blow. A damaged battery is subject to explosion. Properly
dispose of a dropped or damaged battery immediately.
 Batteries can explode in the presence of a source of ignition,
such as a pilot light. To reduce the risk of serious personal
injury, never use any cordless product in the presence of open
flame. An exploded battery can propel debris and chemicals.
If exposed, flush with water immediately.
 Do not charge battery tool in a damp or wet location. Fol-
lowing this rule will reduce the risk of electric shock.
 Use only UL listed USB sources or the FVCH01 battery
charger to charge this device. Use of any non-UL Listed USB
sources may create a risk of fire.
 Do not charge in an area of extreme heat or cold. It will
work best at normal room temperature. To reduce the risk
of serious personal injury, do not store outside or in vehicles.
 Under extreme usage or temperature conditions, battery
leakage may occur. If liquid comes in contact with your
skin, wash immediately with soap and water. If liquid gets
into your eyes, flush them with clean water for at least 10
minutes, then seek immediate medical attention. Following
this rule will reduce the risk of serious personal injury.
 When battery pack is not in use, keep it away from other
metal objects like: paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or a fire.
 Always remove battery pack from your tool when you are
 If a battery powered tool stops during use, refer to the tool
 Always remove battery pack before storing the device.
 Always wear eye protection with side shields marked to
 Keep battery pack dry, clean, and free from oil and grease.
USB lithium cordless
™
 Do not use a battery pack that is damaged or modified. Dam-
 Do not disassemble, modify or attempt to repair a battery
 Do not expose a battery pack or appliance to fire or exces-
 Have servicing performed by a qualified repair person us-
 Do not charge close to combustibles.
 Save these instructions. Refer to them frequently and use them
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in tools at temperatures
down to 14°F. Put the battery pack on a tool and use the tool in a
light duty application. After about a minute, the pack will warm up
and begin operating normally.
CHARGING THE BATTERY PACK WITH A USB-C
CABLE
See Figure 1.
Battery packs are shipped in a low charge condition to prevent
possible problems. Therefore, you should charge prior to first
use. If the charger does not charge the battery pack under normal
circumstances, return both the battery pack and charger to your
nearest Authorized Service Center for electrical check.
 Charge the battery pack only with the recommended charger
 Refer to charger operator's manual for charging instructions or
To charge the battery pack using a UL listed USB source:
 Remove the battery pack from the tool, if applicable.
 Insert the USB-C cable into the battery pack as shown.
 Connect the USB-C cable to a UL listed USB adaptor or power
 Make sure the adaptor or power source is connected to normal
 Remove the USB-C cable and disconnect the adaptor or power
1 - English
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental start-
ing that could cause serious personal injury.
operator's manual for troubleshooting instructions. Charge
battery pack as needed.
comply with ANSI Z87.1. Failure to do so could result in objects
being thrown into your eyes and other possible serious injuries.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any solvents to
clean battery pack.
aged or modified batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
pack that has been damaged.
sive temperature. Exposure to fire or temperature above 265°F
(130°C) may cause explosion.
ing only identical replacement parts. This will ensure that the
safety of the product is maintained.
to instruct others who may use this tool. If you loan someone
this tool, loan them these instructions also.
OPERATION
or a UL listed USB source.
follow the instructions below for USB charging.
source.
household voltage, 120 volts, AC only, 60 Hz.
source once the battery pack is fully charged.