Idiomas disponibles
Idiomas disponibles
shall be easily accessible. Please refer all power source issues to a certified
electrician.
Service and maintain the tire changer regularly as outlined in the
"Maintenance" section of this document. For further information contact:
Hunter Engineering Company
http://www.hunter.com
Equipment Specifications
Equipment Specifications
Electrical (North America)
Voltage:
Amperage:
Wattage:
Electrical (International)
Voltage:
Amperage:
Wattage
Air
Air Pressure Requirements:
Approximate Air Consumption:
Mechanical
Clamping System / Rotating
Speed:
Torque:
Max Tire Diameter:
Maximum Wheel Width:
Rim Diameter Range:
Hydraulic
Hydraulic Pressure:
Hydraulic Flow:
Atmospheric
Temperature:
Relative Humidity:
Altitude:
Decal Information and Placement
Decal Information and Placement
Left Side View
Right Side View
Front View
Equipment Components
Equipment Components
A) Press Arm Roller
C) Upper Bead Roller
E) Mount / Demount Tool Head
G) Platen
I) Flange Plate
K) Joystick Controls
M) Lower Bead Roller
O) Wheel Lift / Go Pedal
Touch Screen Display Components
Touch Screen Display Components
A) Procedure Wheel
C) Green Dot Indicates Current
Selection
E) Process Guide Pane
G) Wheel Dimensions & Inflation Controls
8
208-230 VAC, 1 phase, 50/60 Hz, NEMA
30 amp plug,
L6-30P
24 amperes
5520 watts (peak)
210-240VAC, 50 Hz,
NEMA 30 amp plug,
L6-30P
24 amperes
5320 watts (peak)
125 ± 25 PSI (8.6 ± 1.7 bar)
1 SCFM (27 Liters/Minute)
Center w/Quick Clamp and Cam Plate /
Variable up to 15 rpm CW / CCW
875 ft-lbs (1,186 Nm)
50 in. (1,270 mm)
15 in. (381 mm)
12 in. - 30 in. (305 mm - 762 mm)
1,700 psi (117 bar)
4.1 gpm (16 lpm)
+32°F to +122°F (0°C to +50°C)
Up to 95% Non-condensing
Up to 6000 ft. (1829 m)
Image 2.
Image 3.
Image 4.
Image 5.
B) Press Arm Shoe
D) Camera
F) Wheel Clamp
H) Wheel Lift / Rotation Spindle
J) Touchscreen Monitor
L) Bead Blast Inflator
N) Rotation Pedal
Image 6.
B) Step "Slide-Out" Menu
D) Navigation Menu
F) Real-Time Active Display
Equipment Power and Specifications
Equipment Power and Specifications
Turning Power ON/OFF
Push Button Power Switch
The Hunter Revolution
Tire Changer is equipped with a push button power
™
switch located on the right side of the console, above the emergency stop
switch. Use this switch for normal shut down and restarting procedures.
To prevent loss of data, always use the push button switch on
the side of the console to power the tire changer on and off.
Emergency Stop Switch
Use of the emergency stop switch will NOT shut down the
computer and LCD functions.
The Hunter Revolution
Tire Changer is equipped with an emergency
™
stop switch located on the right side of the console, below the push button
power switch. Push this switch for an immediate termination of all hydraulic
functions, e.g., spindle rotation, tool movement, etc. Pull the switch back out
to resume hydraulic functions.
A) Power
After the Hunter Revolution
Tire Changer is powered on, it will perform a
™
self-check and load screen objects. The main interface screen will appear
indicating the unit is ready for use.
Equipment Installation and Service
Only a Hunter Factory-Authorized Representative should perform installation.
This equipment contains no operator serviceable parts. All repairs must be
referred to a qualified Hunter Service Representative.
Explanation of Symbols
These symbols may appear on the equipment.
l
Operating the Tire Changer
Operating the Tire Changer
Wheel Lift / GO Pedal
Keep hands clear of wheel, tire and rollers during operation.
During normal operation, the GO pedal is pressed the majority
of the time to complete procedures.
Releasing the GO pedal will pause the current procedure. Slide-
out menus on the touch screen procedure wheel may change,
allowing for other options.
In most cases, pressing back down on the GO pedal will
continue the previously paused procedure.
To raise the wheel lift, press and hold down the right side of the pedal.
To lower the wheel lift, press and hold down left side of the pedal.
Once the spindle is vertical, the right side of the pedal becomes the GO pedal.
If the wheel lift is less than vertical, the "GO" function is disabled
until the spindle is vertical.
Image 7.
B) Emergency Stop
Image 8.
Alternating current.
Earth ground terminal.
Protective conductor terminal.
ON (supply) condition.
OFF (supply) condition.
Risk of electrical shock.
Stand-by switch.
Not intended for connection to public
telecommunications network.
English
