Residual Risks; Assembly And Adjustment - Stanley STGL2218 Manual De Instrucciones

RESIDUAL RISKS

Additional residual risks may arise when using the
tool which may not be included in the enclosed safety
warnings. These risks can arise from mis- use, prolonged
use etc. Even with the application of the relevant safety
regulations and the implementation of safety devices,
certain residual risks can not be avoided. These include:
f Injuries caused by touching any rotating/moving parts.
f Injuries caused when changing any parts, blades or
accessories.
f Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
f Impairment of hearing.
f Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
USING AN EXTENSION CABLE
If an extension cable is requred, use an approved extension
cable suitable for the power input of this tool (see technical
data). The minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable
completely. Also refer to the table below.
FEATURES (Fig. A)
1. ON/OFF switch
2. Spindle lock
3. Guard
4. Side handle
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other
than those with depressed center.
Do not use the tool in wet conditions or environments in
the presence of flammable liquids or gases.
This heavy-duty angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool
under supervision.

ASSEMBLY AND ADJUSTMENT

Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
ATTACHING AND REMOVING THE WHEEL
GUARD (Fig. B)
Warning! To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or removing/
installing any accessory. Before reassembling the tool,
press and release the trigger switch to make sure the tool
is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove
facing up.
2. Bring the flange of the guard (3) collar over the groove
(11) of the gear housing.
3. Turn the guard (4) counterclockwise by 150 degrees.
4. Make sure that the screws (20) are tightened.
Removing the guard
1. Loosen the screws (20) on the guard collar.
2. Pull up the guard (3).
Warning! Do not operate the tool when the safety
guard is not in place.
FITTING AND REMOVING A GRINDING
C2, C3)
Warning! Do not use damaged grinding wheels.
.
2
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (6) correctly onto the spindle (7)
(Fig. C1).
3. Place the disc (8) on the flange (6) (Fig.C2). When
fitting a disc with a raised center, make sure that the
raised centre (9) is facing the flange (6).
4. Screw the out flange (10) onto the spindle (7) (Fig. C3)
► the ring on the flange (10) must fae towoards the
► the ring on the flange (10) must face away
5. Press the spindle lock (2) and rotate the spindle (7)
until it locks in position (Fig. C2).
6. Tighten the flange (10) with the two-pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (10) with the
two-pin spanner.
Warning! Do not use a damaged disc.
MOUNTING THE SIDE HANDLE (Fig.D)
f For grinding, screw the side handle (4) tightly into
one of the holes (11) or (12) on either side of the gear
case.
PREPARATION BEFORE USE
f Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding
wheels that are overly worn.
f Make sure that the inner and outer flanges are
attached correctly.
ENGLISH • 21
disc when fitting a grinding disc (A)
from the disc when fitting a cutting disc (B)
Fig. C1,
(