Idiomas disponibles
Idiomas disponibles
users.
▶Maintain power tools. Check for misalignment or jammed moving
parts, breakages and any other condition that might affect the power
tools operation. If it is damaged, the power tool must be repaired.
Many accidents are caused by poorly maintained power tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to jam and are easier
to control.
▶Use the power tool, accessories and cutting tools etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from intended could result in a hazardous situation.
5) SERVICE
Your power tool shoul be serviced by a qualiified specialist using only
standard spare parts. This will ensure that it meets the required safety
standards
SPECIAL SAFETY WARNINGS
▶Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
▶Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting
▶Accessory may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed
▶Metal parts of the power tool "live" and could give the operator an
electric shock.
▶Hold power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed metal parts of the
▶Power tool "live" and could give the operator an electric shock.
▶If possible, always use clamps or a vice to hold your work.
▶Always switch off before you put the tool down.
▶Ensure that the lighting is adequate.
▶Do not put pressure on the tool, such that it slows the motor down.
Allow the bit to screw without
▶Pressure. You will get better results and you will be taking better
care of your tool.
▶Keep the area free of tripping hazards.
▶Only use accessory bits in good condition.
▶Before starting, check that there is sufficient clearance for the bit
under the work-piece.
▶Do not touch the bit after operation. It will be very hot.
▶Keep your hands away from under the work-piece.
▶Never use your hands to remove dust, chips or waste close by the
bit.
▶Rags, cloths, cord, string and the like should never be left around
Instruction manual
▶Support the work properly.
▶If you are interrupted when operating the tool, complete the process
▶Periodically check that all nuts, bolts and other fixings are properly
▶When using the tool, use safety equipment including safety glasses
▶Protective clothing including safety gloves. Wear a dust mask if the
▶Warning! Some dust created by power sanding, sawing, grinding,
▶Activities contains chemicals known to cause cancer, birth defects
▶Lead from lead-based paints,
▶Crystalline silica from bricks and cement and other masonry
▶Your risk from these exposures varies, depending on how often you
▶Even when the tool is used as prescribed it is not possible to
▶Damage to the lungs if an effective dust mask is not worn.
▶Damage to hearing if effective hearing protection is not worn.
1) BATTERIES
▶Never attempt to open for any reason.
▶Do not store in locations where the temperature may exceed 40ºC.
▶Charge only at ambient temperatures between 4ºC and 40ºC.
▶When disposing of batteries, follow the instructions given in the
▶Do not cause short circuits. If connection is made between the
▶Do not heat. If batteries are heated to above 100ºC, sealing and
the work area.
and switch off before looking up.
tightened.
or shield, hearing protection, and
operation creates dust.
drilling, and other construction
or other reproductive harm. Some examples of these chemicals are:
products, and arsenic and chromium from chemically-treated
lumber.
do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
eliminate all residual risk factors. The following hazards may arise
in connection with the tool's construction and design:
ADDITIONAL SAFETY INSTRUCTIONS FOR
BATTERIES AND CHARGES
Use only batteries and charges applicable for this
machine.
section "Protecting the environment".
positive (+) and negative (-) terminal directly or via accidental
contact with metallic objects, the battery is short circuited and an
intense current will flow causing heat generation which may lead to
casing rupture or fire.
insulating separators and other polymer components may be
damaged resulting in electrolyte leakage and/or internal short
ref. 08373
ES
PT
EN
FR
