Idiomas disponibles
Idiomas disponibles
Installation (continued)
3A
Installing the mounting
plate cover for Wall/Eave
mount option
Installing the mounting
plate cover for Wall/Eave
For mounting to standard junction boxes
mount option
NOTE: The fixture comes with the threaded 1/2" Swivel
NPS threaded knuckle mount (H) and the mounting plate
cover (C) is in the box.
Place the sealing gasket (FF) on the threaded knuckle
NOTE: The fixture comes with the knuckle stem and the
stem (H) and route fixture wires through the hole of
wall/eave mounting base plate (C) is in the box.
the mounting plate cover (C), being careful not to
pinch the wires (fig 7).
Remove the conduit locknut (G) from the knuckle
mount, then place the sealing gasket (FF) on the
Place the fixture head (A) in the required orientation
knuckle stem and thread wires through the hole of
with the mounting plate cover (C). Place the lock
the mounting plate cover (C), being careful not to
washer (EE) and wing nut (DD) onto the threaded
ping the wires. (Fig 7)
knuckle mount (H) and tighten the wing nut (DD)
(fig 8).
Place the fixture head (A) in the required orientation
with the mounting cover plate (C). Place the lock
Note: Adjust the desired left to right orientation of the
washer (EE) on the threaded knuckle stem (H) and
fixture head (A) with the mounting plate cover (C).
Tighten the knuckle mount (H) to the mounting plate cover
tighten the wing nut (DD) (fig 8).
(C) with conduit locknut (G) (pre-installed) (fig 9)
IMPORTANT: It is important to adjust the desired left to
right orientation of the fixture head (A) with the mounting
plate cover (C) at this step (fig 9).
(fig 7).
(fig 7).
(fig 8).
(fig 8).
(fig 9).
(fig 9).
3B
Installing with swivel knuckle
mount for Ground mount option
3B
For mounting to weather proof junction box or
Installing with swivel knuckle
landscape ground stake
mount for Ground mount option
NOTE: The fixture comes with 1/2" NPS threaded
knuckle mount (H) and is compatible with standard
For mounting to domed junction box or landscape stake
weather proof junction box cover plates or landscape
ground stakes with 1/2" NPSM Pipe Thread
NOTE: The fixture comes with 1/2" NPS threaded
Place the sealing gasket (FF) on the threaded knuckle
knuckle mount (H) and is compatible with standard
stem (H) and route fixture wires through the hole of the
domed junction box cover plates or landscape stakes
weather proof junction box cover or landscape ground
stake, being careful not to pinch the wires.
(fig 10 and fig 11).
Place wires through the hole in the domed junction
box cover plate or landscape stake (fig 10 and fig 11).
Screw threaded knuckle mount (H) into the center hole
of the weather proof junction box cover or landscape
Remove the conduit locknut (G) from the knuckle
ground stake. Use the pre-installed conduit locknut (G)
mount (H).
to tighten threaded knuckle mount (H) into place.
Screw 1/2" NPS threaded knuckle mount (H) into the
Loosen the hex head screw on swivel portion of the
center hole of the domed cover plate or landscape
knuckle mount (H) using the provided allen wrench-2(HH)
stake, if hole isn't threaded, use conduit locknut (G)
and select desired angle. Tighten the hex head screw to
to tighten fixture into place.
secure in place.
Loosen the thumbscrew in the center of the knuckle
mount (H) and select desired angle. Tighten thumb
screw to secure into place.
(fig 10).
(fig 10).
(fig 11).
(fig 11).
6
Please contact 1-844-548-3776 for further assistance.
Weather poof
junction box
cover plate
(Domed
junction bnox
cover plate)
Landscape
Ground Stake
(Landscape
stake)
HOMEDEPOT.com
