EINHELL TE-AG 125 CE Manual De Instrucciones Original página 31

5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Fitting the additional handle (Fig. 2)
•
The angle grinder must not be used without
the additional handle (3).
•
The additional handle can be secured in any
of three positions (A, B, C).
Tool side
Left (position A / as
shown)
Right (position B)
Top (position C)
5.2 Setting the guard (Fig. 3)
•
Switch off the tool. Pull the power plug.
•
Adjust the guard (4) to protect your hands
so that the material being ground is directed
away from your body.
•
The position of the guard (4) can be adjusted
to any specific working conditions. Undo the
clamp handle (a) and turn the cover (4) into
the required position.
•
Ensure that the guard (4) correctly covers the
gear wheel casing.
•
Secure the clamp handle (a) again.
•
Ensure that the guard (4) is secure.
Take care that the safety device is secure.
Never use the angle grinder without the
guard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi tted in place. Vibrating wheels are to be replaced
immediately.
6. Operation
6.1. Switch (Fig. 4)
The angle grinder comes with a safety switch
which is designed to prevent accidents. To start,
push the locking lever (a) forwards, then press the
On/Off switch (2).
Anl_SA_TE AG 125 CE_SPK8.indb 31 Anl_SA_TE AG 125 CE_SPK8.indb 31
GB
Suitable for
Right-handed users
Left-handed users
Using cutting wheels
- 31 -
6.1.1 Speed controller (Fig. 5)
You can select the speed by turning the speed
controller (6).
Switch position 1: approx. 3,000 rpm
Switch position 2: approx. 6,000 rpm
Switch position 3: approx. 8,000 rpm
Switch position 4: approx. 9,800 rpm
Switch position 5: approx. 10,500 rpm
Switch position 6: approx. 12,000 rpm
The best speed depends on the area of appli-
cation and the maximum rated speed of the
grinding/sanding tool. Select a speed in the range
from 3,000 to 12,000 rpm using the speed control
switch (6). You can choose from 6 diff erent switch
positions. The speeds in the various switch posi-
tions are as follows:
Plus direction: Higher speed
Minus direction: Lower speed
6.1.2 Status indicator (Fig. 1)
The status indicator (7) lights up when the power
plug is connected.
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.2 Changing the grinding wheels (Fig. 7 / 8)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in
the additional handle (3). Pull the face spanner (5)
out of the additional handle (3) when you need it.
Important! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Pull out the power plug.
•
Simple wheel change by spindle lock:
•
Press the spindle lock and allow the grinding
wheel to latch in place.
•
Open the flange nut with the face spanner.
•
(Fig. 7)
•
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still! You must keep the spindle lock pressed
while you change the wheel!
07.02.2019 08:20:48 07.02.2019 08:20:48