Splasher Components And Spare Parts Diagram; Hose Assembly; Attaching Hose Weights; Weir Installation - Astralpool SPLASHER Manual De Instrucciones

Features and benefits of your SPLASHER

SPLASHER Components and Spare Parts diagram

1 2
3
7
12
11
6
8
5
10
4
9
13
14
EASY OUT JOGGER CONE:
Place Easy Out Jogger between 2nd and 3rd hose length, small side facing the weir and the
bigger side facing the cleaner. The Easy Out Jogger Cone will sit/lie on top of the water
SPLASHER Assembly
1 2 3
5 6 7
1. Fit the flexi foot to the cleaner main body, ensuring the main body lower flange is properly secured into
the flexi foot locating groove (picture 1)
2. Place the inner top of the fined disc onto the flexi foot pad flange and peel over until the disc is secure
between the flange and top of the flexi foot pad. The fins of the disc and the word "TOP" should face
the cleaner main body. (picture 2)
3. Place the cleaner shroud (Silver) over the inner tube and slide down onto the main body. The main
body has a location key that needs to align with a groove within the shroud. This ensures the shroud
is installed correctly. (picture 3)
4. Place the cleaner float assembly over the inner tube and on top of the shroud. This also needs to
06
bealigned to the main body location key. (picture 4)
No Code Description
1 630-9080 Hose Weight
2 570-0007 Easy Out Jogger
3 630-6210 1m Unifit Hose
4 630-9068 Diaphragm Round
5 630-9069 Inlet Plate
6 630-9079 Cartridge
7 630-9067 Inner Tube
8 630-9083 Main Body
9 630-9073 Shroud
10 630-9078 Float Set
11 630-9072 Deflector Wheel
12 630-9085 Outer Tube
13 630-9070 Flexi Foot
14 630-9071 Finned Disc
Include universal adaptor.
4
8
5. Slide the cleaner deflector wheel over the inner tube until located on top of the float assembly. The
deflector wheel does not align with the locating key on the main body and is able to spin freely on the
top section of the main body. (picture 5) NOTE: The deflector ring can be removed and replaced with
a SPLASHER cone to enhance performance, depending on pool shape
6. Slide the outer tube assembly down the inner tube and screw the nut into place as this will secure the
deflector wheel. (picture 6)
7. Connect sufficient lengths of cleaner hose to cover the distance from the pool skimmer box or weir t o
the furthest point of your pool, plus one length. (picture 7)
8. Congratulations your SPLASHER pool cleaner is ready for installation into your pool!

Hose assembly:

The pump must be on when you check the hose length. The hose
contracts when the pump is operating and will be longer when
the pump is off.
While the cleaner is operating:
1. Position cleaner at the furthest point of the pool from where
it's attached. (Use a pool pole and brush to easily position the
cleaner in the pool.)
2. The hose should be long enough to reach the end of the pool,
plus one hose section. (The hoses are universal hoses and fit
directly into each other).
3. If there is excess hose, be sure to remove the sections from the center portion of hose. This
avoids disturbing the hose weight placement.
4. Save extra hose sections for use as needed for replacement. Always keep extra hoses stored
in a straight position.
Note: Turn pool pump off when adding or removing hose sections.

Attaching hose weights

To determine correct hose balance,
turn the pump off and note the cleaner's
position in the pool. Correct Hose Balance:
Cleaner seal sits flat on the pool floor and
the drive tube makes 45° angle with the
pool floor.
For maximum cleaning coverage, the hose
does not pull up or down on the unit. Adjust
hose weight one inch at a time, as needed,
to achieve proper hose balance.
In pools with both shallow and deep areas,
adjust hose weights first in the deep area
and then in the shallow area.
Installation
Hose Weight (1-2 hose lengths from cleaner)

Weir installation

Universal Adaptor
Skimmer Plate
Incorrect Correct Incorrect
Hose Lengths
Splasher
ENGLISH
07