Idiomas disponibles
Idiomas disponibles
TECHNICAL DATA
TRIM ROUTER
Production code ................................................................................................................
Rated no-load speed ........................................................................................................
Cage stroke.......................................................................................................................
Collet diameter .................................................................................................................
Battery voltage ..................................................................................................................
Router diameter max ........................................................................................................
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12 Ah) ......................................
Recommended ambient operating temperature .............................................................
Recommended battery types ...........................................................................................
Recommended charger....................................................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ................................................................
Sound power level (Uncertainty K=3dB(A)) ....................................................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN
62841.
Vibration emission value a
..............................................................................................
h
Uncertainty K= ..................................................................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or
poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the
job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm,
organization of work patterns.
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow al l instructions
listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
TRIM ROUTER SAFETY WARNINGS
Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by your hand or against the body leaves it
unstable and may lead to loss of control.
Only use rotary cutting bits are suitable for the speed of the tool. The rotary
cutting bit must be suitable for speed up to 31000 min
.
-1
Only the collets may be used, which are supplied with the machine.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when Always wear goggles
when using the machine. It is recommended to wear gloves, sturdy non slipping
shoes and apron.
Never reach into the danger area of the plane when it is running.
Always use the protective shields on the machine.
Only use tools whose permitted speed is at least as high as the highest no-load
speed of the machine.
Chips and splinters must not be removed while the machine is running.
Only use professionally grinded router cutters.
Only use router cutter with correct shank diameter.
The workpieces should be clamped down before cutting.
Put the router back to original position after usage (loosen clamping lever to secure
cage).
Only move the workpiece in counter rotation to cutter (only work oppositely
oriented)! For security, use devices such as safety- and pressure device, guide
slide, rip fence, etc.
The dust produced when using this tool may be harmful to health (e.g. when
working oak or beech wood, stones, paint, which could contain lead or other harmful
chemicals). Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly, e.g. with a
vacuum cleaner.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device
on again while the insertion tool is stalled, as doing so could trigger a sudden recoil
with a high reactive force. Determine why the insertion tool stalled and rectify this,
paying heed to the safety instructions.
32
ENGLISH
M18 FTR8
...........................................................................4834 96 02...
...000001-999999
............................................................. 10000 - 31000 min
-1
.................................................................................38 mm
........................................................................8 mm, 6 mm
.................................................................................18 V
.................................................................................38 mm
.............................................................1,79 kg ... 2,86 kg
.......................................................................-18...+50 °C
....................................................... M18 B..., M18 HB ...
......................................................M12-18 ..., M1418 C6
............................................................................80,02 dB (A)
............................................................................91,02 dB (A)
..............................................................................0,88 m/s
2
................................................................................1,5 m/s
2
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or
waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause
severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them.
Milwaukee Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry
at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with soap
and water. In case of eye contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to a
short circuit, never immerse your tool, battery pack or charger in fl uid or al-low a
fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products, etc., Can cause a
short circuit.
SPECIFIED CONDITIONS OF USE
The router can be used for rabbeting, rounding off , chamfering, routing of edges, as
well as pitting in wood and plastic.
This router can be used with the following types of rotary cutting bits:
• slotter bit
• roundover bit
• trim bit
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant regulations and the
directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following
harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-17:2017
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Winnenden, 2022-02-07
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
2012/3032 (as amended) and that the following designated standards have been
used:
BS EN 62841-1:2015
BS EN 62841-2-17:2017
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 63000:2018
Winnenden, 2022-02-07
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully charged.
To obtain the longest possible battery life remove the battery pack from the charger
once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause high
current draw, the tool will vibrate for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could become
to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national
and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the process has
to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent short
circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine
type printed as well as the six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Accessory - Not included in standard equipment, available as an
accessory.
Please read the instructions carefully before starting the machine.
Wear eye protection.
Do not dispose of waste batteries, waste electrical and electronic
equipment as unsorted municipal waste. Waste batteries and waste
electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be
removed from equipment.
Check with your local authority or retailer for recycling advice and
collection point.
According to local regulations retailers may have an obligation to
take back waste batteries and Waste electrical and electronic
equipment free of charge.
Your contribution to re-use and recycling of waste batteries and
waste electrical and electronic equipment helps to reduce the
demand of raw materials.
Waste batteries, in particular containing lithium and waste Electrical
and electronic equipment contain valuable, recyclable materials,
which can adversely impact the environment and the human health,
if not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
33
