Idiomas disponibles
Idiomas disponibles
OPERATION
WARNING:
Do not allow familiarity with the product to make you careless.
Remember that a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields or goggles marked to
comply with ANSI Z87.1. Failure to do so could result in fluids entering your eyes
resulting in possible serious injury.
WARNING:
Use safety equipment. Protect your eyes, skin, and lungs while
mixing, filling, spraying, and cleaning. Failure to do so may result in serious personal
injury and damage to property.
WARNING:
Do not use this sprayer or enter the spray area if you have a
pacemaker, implantable cardioverter defibrillator (ICD), internal pump, or any other
similar medical device. Do not use on or near electrical medical equipment.
CAUTION:
To reduce the risk of electric shock, do not touch the nozzle during use.
NOTICE: Before each use, inspect the entire product for damaged, missing, or loose parts
such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are replaced. Please contact
customer service or an authorized service center for assistance.
What Solution Can You Use?
You may use this product for the purpose listed below:
• For use with most consumer grade disinfectants and sanitizing solutions.
DO NOT USE THIS SPRAYER WITH BLEACH, HYDROGEN PEROXIDE, PINE SOL OR PINE
OIL BASED SOLUTIONS. DO NOT USE WITH VINEGAR.
• Know the contents of the chemical being sprayed. Read all Safety Data Sheets
(SDS) and container labels provided with the chemical. Follow the chemical
manufacturer's safety instructions. It is a violation of federal law to use an
EPA-approved disinfectant in a manner inconsistent with its labeling.
Filling the Tank
When adding spray solutions, you may add water and the desired chemical solution directly
into the tank, or use a solution that has been premixed in a separate container, then poured
into the sprayer, using a funnel if needed. For either method, remember:
• Liquids used must be as thin as water. Thicker liquids will not spray properly.
• Do not overfill the tank.
NOTE: If using a measuring container or funnel to fill the tank, be sure to thoroughly
clean and rinse these items after use. If premixing the spraying solution, rinse the
container used for mixing.
TO FILL:
• Turn off the electrostatic function and remove the battery from the unit.
• Unscrew the cap and remove it from the tank.
• Fill the tank with the desired liquid, up to 2 gal.
NOTE: To ensure proper operation of the sprayer, DO NOT fill past the max fill line.
Screw the cap back onto the sprayer, making sure it is tightened securely.
NOTE: Wipe the outside of the tank with a dry cloth and clean up any spills before
inserting the tank.
• Reinstall the battery pack.
NOTICE: It is important to thoroughly clean the unit after each use. Allowing liquid to
remain in an idle tool for an extended period may cause its moving pieces and connectors
to seize up.
A. Cap
B. Tank
4
A
B
Inserting the Tank
Push the male barb on the hose onto the female quick connect on the tank.
Pull on the hose to be certain it is properly secured.
NOTE: When using the shoulder bag option, place the tank inside the bag before
attaching the hose to the tank.
A. Coiled Hose
B. Hose Barb
C. Quick Connect Hose
D. Tank
E. Shoulder Bag
C
B
A
Using the Quick Connect Hose
TO ATTACH HOSE:
• Pull back the quick-connect collar.
• Push the hose into place onto the male barb on the back of the sprayer.
• Push the collar forward so that the hose is secured properly.
• Check to see that the hose is secure.
TO DISCONNECT HOSE:
• Pull back and hold the quick-connect collar.
• Remove the hose by pulling it from the quick-connect collar.
NOTE: Be careful when disconnecting the hose from the tank because the liquid in the
hose will drain from that end. Drain remaining liquid back into container.
A. Hose Barb
B. Quick Connect Hose
Connecting the Battery Pack
WARNING:
Always remove battery pack from your tool when you are
assembling parts, making adjustments, cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could cause serious personal injury.
TO INSTALL:
1. Align the grooves on the battery pack with the raised ribs
in the battery port and place the battery pack in the tool.
2. Make sure the latches on each side of the
battery pack snap in place and that the
battery pack is secured in the tool
before beginning operation.
A. Battery Pack
B. Battery Port
C. Latch
D
E
C
B
A
A
B
A
C
B
C
