Bresser 47-01170 Instrucciones De Uso página 12

6. Eyepiece
Remove one eyepiece from its eyepiece holder (6) and slide it into the
eyepiece connection (3). Tighten the holding screws (No. 5). Start with
the lowest magnification eyepiece, which has the highest focal length
printed on it (e.g. 20 mm or 25 mm, depending on your model) to locate
objects and find the correct focus. If you have the object you want
to view centred in the field of view, switch to a higher magnification
by using an eyepiece with shorter focal length. After changing the
eyepiece, it might be necessary to adjust the focus again (see section
8).
7. Dust cover
Remove the dust cover (15) that protects the objective lens of the opti-
cal tube opening (2).
8. Focus wheel
To get objects into focus, your telescope is equipped with a precise
focus control. When you use the telescope for the first time, you might
need to turn the focus wheel (4) multiple times to achieve a focused
image. To try it out, pick a landmark or a building far away in daylight
or bright twilight, and turn the focus wheel until the object comes into
focus. Remember, objects to be observed cannot be closer than 20
metres away.
Part II – Handbox
1. Batteries
Remove the cover of the battery compartment (11), located on the top
side of the mount's base, and insert the batteries in the battery holder
(No. 2). Use 6 AA batteries and make sure the polarities are aligned
correctly. Place the holder into the compartment and cover it. Do not
use rechargeable batteries.
2. Handbox
Ensure that the on/off switch is in the off position (No. 8). Remove the
handbox from the handbox tray (7), and plug one end of the cable into
the port labelled with "HBX" and the other one into the RJ-45 port of
the handbox. Flip the switch to the on position. The handbox display
should light up, accompanied by a sound.
3. Setup
Time and Date
After turning on the handbox, you will be prompted to enter the date
and time. Do so by navigating with the arrow keys and entering the
numbers with the number pad (7) on the handbox. When done, press
the centre key (5), located between the arrow keys.
Daylight saving time
If the daylight saving time is in effect, select status:on. If daylight saving
time is not in effect, select status:off.
12
Manual_4701180-4701181_de-en-fr-it-es-ru_BRESSER_v082020a.indd 12 Manual_4701180-4701181_de-en-fr-it-es-ru_BRESSER_v082020a.indd 12
Location
When asked for your location, you can either choose a city near you
by selecting the 'Country & City' option or enter your GPS coordinates
by selecting 'Custom Site'.
a) Country & City
Select the country where you are by using the up and down arrow
keys. Then select the city by using the left and right arrow keys. When
done, use the centre key (5) to select the location.
b) Custom Site
Enter the details of your location as follows:
Name: Enter a custom name for your location.
Lon: Enter the longitudinal coordinate of your location.
Lat: Enter the latitudinal coordinate of your location.
Zone: Enter the time zone of your location.
Example:
Name:
Berlin ; Lon: E013° 25` ;
Lat: N52° 30` ; Zone: E01
Time zone east of Greenwich:
E01-E12
Time zone west of Greenwich:
W01-W12
Greenwich time zone (GMT):
E00 oder W00
OTA (Optical Tube Assembly) Zero
Here you will be asked to provide the orientation of the telescope.
In the 'Azi:' field, enter '000'.
In the 'Alt:' field, enter '00'.
Open the Altitude and Azimuthal locking knobs. Adjust the telescope
so that the tube opening (2) is pointing directly north and is level. It
is recommended that you use the included compass (18) and bubble
level to make sure the device is positioned accurately. You can put the
compass into the eyepiece connection (3). Then retighten the locking
knobs.
4. Alignment
In order to use your telescope's Go To mode, you must align the tel-
escope properly so it knows where it is pointing when it is turned on.
There are three ways to align your telescope: one-, two- and three-star
alignment.
Step 1: To start the alignment, press the centre key (5) on the handbox
and select the first menu option, 'Telescope Align'. There you will be
able to choose between one-, two- and three-star alignment.
17.08.2020 08:07:54 17.08.2020 08:07:54