Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EN
sensors vessels.)
Magnetic stainless
Stainless steel pot Iron blast pan
Stainless Steel pot
steel pan
3.2 Please kindly according to the below requirement if necessary to use the vessel is not
equipped.
² Pan/pot must be suitable for induction cooker.
² Pan/pot should be tried out if it's bought by self to see if there are unusual phenomena.
² Pan/pot bought by self should be flat and come with the cover with gas vent
4. Maintenance and Daily Care
1. Remove the power plug prior to clean the unit. Do not clean it until the surface cools down.
2. Glass plate, panel and the shell:
Soft cloth for slight stain.
1
For greasy, dirt, blot by using a clean damp cloth with neutral detergent.
2
3. While the radiator-fan working, dust and dirt would remain on the gas vent, please clean it by
brush or cotton stick regularly.
4. Remember do not washing the unit by water directly to avoid damaging.
5. To protect induction cooker, be sure to have a good contact between plug and socket before
using.
6. Do not pull out the power cord directly during operation. To extend the appliance's using life,,
press the "ON/OFF" button first, then pull out the power cord.
7. In order to make operating time longer, the fan would still working for cooling the plate, it is
better to plug out after the fan stops working.
8. Please pull out the power cord and put it away when not used for a long time.
9. Some models have structural design to against cockroaches, if needed, can put something
like.mothball to expel the cockroaches.
Any other servicing should be performed by an authorized service representative.
5. Troubleshooting and Treatment
During operations, if any error occurred, please check the following table before calling for
service. Below are common errors and the checks to perform.
Magnetic
Iron board pan
stainless
Iron pan
09
Symptoms
Check points
After connecting the
Is the electricity in suspension?
power and pressing the
"power" key, the
Is the fuse broken down?
appliance has no
response.
Is the plug connected firmly?
Heating being
Incompatible cookware or no
interrupted in normal
cookware is used?
use and a "Beep" will be
Is the cookware not considerably
heard.
placed form the center of the heating
zone?
Is the cookware being heated but
continually being removed?
Symptoms
Check points
No operation during the
Is the cookware empty or the
heating being in use.
temperature too high?
Is the air intake/exhaust vent clogged
or dirt has accumulated?
Is the cooker working over 2 hours
without any external instruction?
Error codes occur.
E0 Without cookware or Incompatible
cookware used
E1 IGBT sensor open circuit/short
circuit
E2 Internal overheat
E3 Over-voltage
E4 Under-Voltage
E5 Top plate sensor open/short
circuit
E6 Top plate overheat
If the above remedies/controls can not fix the problem, unplug the appliance immediately,
contact Service Centre for inspection and repairing, note the error code and report it to Service
Centre Ltd. To avoid any danger and damage to the appliance, do not disassemble or repair it by
yourself.
6. Product Specifications
Model
Rated Voltage
Power
Remedy
Use after resuming the
electricity.
Check the root causes
carefully. If the problem cannot
be fixed, please contact
Service Centre for checking
and repairing.
Replace compatible cookware
for the induction cooker.
Place the cookware at the
center of the defined heating
zone.
Place a cookware inside the
heating zone.
Remedy
Please check whether the
appliance is being misused.
Remove the stuff clogging the
air intake/exhaust vent.
Operate the appliance again
after cooling down.
Reset cooking modes or use
timer function.
When showing error signal E0,
E2 and E6, please check
whether the cookware is not
suitable, or switch on the
appliance again after it is
cooled down naturally. When
showing E1, E3-E5, please
contact Service Centre for
checking and repairing.
BGMP-9135
220-240V~50/60Hz
2000W
10
EN
Tabla de contenido
