Idiomas disponibles
Idiomas disponibles
KEEP THIS MANUAL
You will need the manual to check safety and caution rules,
assembly instructions, maintenance and operating procedures.
SAFETY INSTRUCTIONS
NOTICE: When using your tool, basic safety precautions
should always be followed to reduce the risk of personal
injury and equipment damage.
Read all instructions before using your tool.
1.
Keep the work area in order. Benched and cluttered areas
are accident prone.
2. Observe the conditions of the work area. Do not use
machines or power tools in wet or damp areas. Do
not expose your tool to rain. Keep the work area well
lit. Do not use power tools in the presence of
flammable gases or liquids.
3. Protect yourself against electric shocks. Prevent
body contact with grounded surfaces such as pipes,
radiators, and refrigerators.
4. Keep children away. The machine must not be used by children
or persons with reduced physical, sensory or mental
capabilities, nor by persons with no experience or knowledge
in its use, unless they are supervised by a person responsible
for their safety or have received prior instructions on the use
of the machine. Children must be supervised to ensure that
they do not play with the machine. Close supervision should
be maintained if children or handicapped persons come near
or use any type of electrical appliance.
5. Keep the equipment stored when not in use. When not in
use, the tool should be stored in a dry, dust-free place. Always
keep your tool locked away so that it is out of the reach of
children.
6. Do not force the tool. It will do its job better and be safer
within the range for which it was designed. Do not use
improper attachments in an attempt to exceed the tool's
capacity.
7. Use the appropriate power tool. Do not use tools that are
too weak for heavy work. Do not use power tools for heavy
work for which they are not designed.
8. Wear appropriate clothing. Do not wear loose clothing,
gloves, neckties or jewelry that can get caught in moving
parts. Do not wear slippery footwear. Use a hair guard to
retain long hair.
9. Wear eye protection. Always use appropriate safety
accessories according to the Mexican Official
Standard (NOM), such as goggles, face shields and
dust masks, when working with materials that release
metal parts, chips or chemical dusts.
10. Do not use the power cable for purposes for which it is not
intended. Do not carry the tool by the cord and do not pull
on the cord to disconnect the plug from the socket base.
Protect the cord from heat, oil and sharp machinery.
11. Maintain proper balance on your feet at all times. Do not
reach over the machine or cross over when it is in operation.
12. Do not extend your radius of action. Avoid any posture that
causes fatigue. Make sure that your position is safe and that
you keep your balance.
13. Keep tools in the best condition. Keep tools clean for best
performance and safety. Follow instructions for lubrication
and change of accessories. Check tool cables periodically
and if damaged, take them to a Truper Authorized Service
Center for repair. Handles should always be kept clean, dry
and free of oil and grease.
2
14. Disconnect the tool. Disconnect the tool when
not in use before servicing.
15. Reduce the risk of accidental start-up. Do not
carry any tools with your finger on the switch while it
is connected to the power supply. Make sure the switch
is in the "OFF" position before connecting the power
cord.
16. Outdoor extensions. Use only approved and
properly marked outdoors extension cords.
17. Be alert. Watch what you are doing, use common sense. Do
not operate any tool when you are tired.
18. Check for damaged parts. Before continuing to use the
machine, guards or other moving parts that may be damaged
should be carefully checked to make sure they operate
properly and will work as intended. Check also the alignment
of the moving parts, if they are jammed or if there is any
probable breakage of the parts, check also the mounting, as
well as any other condition that may affect the operation of
the tool. All components must be properly assembled and
meet the requirements to ensure proper operation of the tool.
A guard or other part that is damaged should be properly
repaired or replaced. Any damaged control switch should be
replaced by a Truper Authorized Service Center. Do not use
any power tool on which the switch has no contact.
19. Replacement of parts and accessories. When
replacement parts are required, use only genuine
Truper replacement parts intended for use with this
tool.
20. CAUTION!! For your personal safety use only
accessories or additional equipment specified in the
operating instructions or recommended by the tool
manufacturer. The use of accessories other than those
specified in the operating instructions may result in
personal risk.
21. Hearing protection. Use ear protectors when
performing services that make noises above 85 dB.
If dust extraction and collection devices are connected to the tool,
check their connections and use them correctly.
The use of these devices reduces the risks related to dust.
