PPA DOG STEEL CUSTOM Manual De Instrucciones

1. OVERVIEW
DOG STEEL CUSTOM electromagnetic lock has been developed to meet the user needs, in compliance
with the strictest quality, security and comfort standards for its users. It is produced with steel plates with
epoxy-coat finishing to increase its service life; It is available in 127 or 220 V.
The electromagnetic lock can be activated at the moment the gate operator is activated or manually by
DOG STEEL CUSTOM
means of a proper key. It automatically locks the gate after the gate is closed.
NOTE:
We strongly recommend using a timer board when installing the 'DOG STEEL CUSTOM'
ELECTROMAGNETIC LOCK.
ELECTROMAGNETIC LOCK
The timer board has been developed to decrease electric energy consumption by the product. The
timer module is easy to install; all one must do is connect two specific wires to the control board of
the operator; whenever the motor is activated in order to open the gate, the timer activates the lock
during the average time of 5 seconds, and then it will turn itself off.
2. TECHNICAL FEATURES
SPECS - 127V SPECS - 220V
- Current of 0.95 A - Current of 0.95 A
TECHNICAL MANUAL TECHNICAL MANUAL TECHNICAL MANUAL TECHNICAL MANUAL
- Inductance of 150 mH - Inductance of 230 mH
- Resistance of 109 Ohms - Resistance of 169 Ohms
- Output power of 125 W - Output power of 210 W
- Cycles/Hour 40 - Cycles/Hour 40
MATERIAL COMPATIBLE WITH
- 1020 Steel - Overhead / Sliding / Swing gates
3. INSTALLATION
1. Carefully read all the instructions herein before starting the installation procedures.
2. The electromagnetic lock must be installed on the inner side of the gate. Mounting depends on
each kind of gate. Therefore, the installer is supposed to choose the proper manner / position for
every individual installation.
3. Fasten the mounting plate (base) on the gate leaf and use the pin to centralize the ramp (gate stopper).
4. Fasten the ramp and afterwards fasten the lock by means of the screws.
5. Once the set is properly mounted, perform the testing, by manually opening and closing the gate.
NOTE:
'DOG STEEL CUSTOM' ELECTROMAGNETIC LOCK is endowed with a rectifier bridge on
its electronic circuit.
4. WIRING DIAGRAMS
WIRING DIAGRAM FOR AN OPERATOR WITH THE LOCK CONNECTOR ON THE CONTROL
BOARD ONLY
WARNING WARNING
Do not use the device without Do not use the device without
referring to this manual first. referring to this manual first.
NOTE:
The PPA
RELAY MODULE is sold LOCK CONNECTOR
P09520 - 09/2021
Rev. 0 OPERATOR'S CONTROL
separately.
BOARD
1. OVERVIEW
DOG STEEL CUSTOM electromagnetic lock has been developed to meet the user needs, in compliance
with the strictest quality, security and comfort standards for its users. It is produced with steel plates with
epoxy-coat finishing to increase its service life; It is available in 127 or 220 V.
The electromagnetic lock can be activated at the moment the gate operator is activated or manually by
means of a proper key. It automatically locks the gate after the gate is closed.
NOTE:
We strongly recommend using a timer board when installing the 'DOG STEEL CUSTOM'
ELECTROMAGNETIC LOCK.
The timer board has been developed to decrease electric energy consumption by the product. The
timer module is easy to install; all one must do is connect two specific wires to the control board of
the operator; whenever the motor is activated in order to open the gate, the timer activates the lock
during the average time of 5 seconds, and then it will turn itself off.
2. TECHNICAL FEATURES
SPECS - 127V SPECS - 220V
- Current of 0.95 A - Current of 0.95 A
- Inductance of 150 mH - Inductance of 230 mH
- Resistance of 109 Ohms - Resistance of 169 Ohms
- Output power of 125 W - Output power of 210 W
- Cycles/Hour 40 - Cycles/Hour 40
MATERIAL COMPATIBLE WITH
- 1020 Steel - Overhead / Sliding / Swing gates
3. INSTALLATION
1. Carefully read all the instructions herein before starting the installation procedures.
2. The electromagnetic lock must be installed on the inner side of the gate. Mounting depends on
each kind of gate. Therefore, the installer is supposed to choose the proper manner / position for
every individual installation.
3. Fasten the mounting plate (base) on the gate leaf and use the pin to centralize the ramp (gate stopper).
4. Fasten the ramp and afterwards fasten the lock by means of the screws.
5. Once the set is properly mounted, perform the testing, by manually opening and closing the gate.
NOTE:
'DOG STEEL CUSTOM' ELECTROMAGNETIC LOCK is endowed with a rectifier bridge on
its electronic circuit.
4. WIRING DIAGRAMS
WIRING DIAGRAM FOR AN OPERATOR WITH THE LOCK CONNECTOR ON THE CONTROL
BOARD ONLY
NOTE:
The PPA
RELAY MODULE is sold
LOCK CONNECTOR
separately. OPERATOR'S CONTROL
BOARD
PRODUCT SIZE
- Length: 110 mm (~4.4 in)
- Width: 106 mm (~4.2 in)
- Height: 76 mm (~3 in)
- Pin size: 20 mm (~0.8 in)
- Pin diameter: 18 mm (~0.8 in)
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
PPA RELAY MODULE
127 VAC
OR
220 VAC
According to the
electromagnetic lock voltage.
PRODUCT SIZE
- Length: 110 mm (~4.4 in)
- Width: 106 mm (~4.2 in)
- Height: 76 mm (~3 in)
- Pin size: 20 mm (~0.8 in)
- Pin diameter: 18 mm (~0.8 in)
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
PPA RELAY MODULE
127 VAC
OR
220 VAC
According to the
electromagnetic lock voltage.
WIRING DIAGRAM FOR AN OPERATOR WITH TIMER, WITHOUT THE LOCK CONNECTOR ON
THE CONTROL BOARD
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
WIRING DIAGRAM FOR AN OPERATOR WITH TIMER AND THE LOCK CONNECTOR ON THE
CONTROL BOARD
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
PPA RELAY MODULE
127 VAC
OR
LOCK CONNECTOR
220 VAC
OPERATOR'S CONTROL
According to the
BOARD
electromagnetic lock voltage.
WIRING DIAGRAM FOR AN OPERATOR WITH TWO LOCKS, TIMER AND LOCK CONNECTOR
ON THE CONTROL BOARD
LOCK CONNECTOR
OPERATOR'S CONTROL
BOARD
WIRING DIAGRAM FOR AN OPERATOR WITH TIMER, WITHOUT THE LOCK CONNECTOR ON
THE CONTROL BOARD
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR, Industry and Commerce of Automatic Gate Operators Ltd., registered with
BLACK WIRE AND WHITE WIRE = 127 V
the CNPJ (National Registry of Legal Entities) under Number 52.605.821/0001-55, located at
BLACK WIRE AND RED WIRE = 220 V
3526 Dr. Labieno da Costa Machado Avenue, Industrial District, Garça – SP – Brazil, Zip Code
17400-000, manufacturer of PPA Products, hereby guarantees this product against design,
manufacturing or assembly defects and/or supportively as a result of material quality flaws
that could make its intended use improper or inadequate, within a legal period of ninety days
from time of acquisition, provided that the installation instructions described in the instruction
manual are observed.
Due to the credibility and trust placed on PPA products, we will add 275 more days to the period
mentioned above, reaching a warranty period of one year, likewise counted from the time of
acquisition proven by consumer through proof of purchase (Customer Receipt).
In case of defect, within the warranty period, PPA responsibilities are restricted to the repair
or substitution of the product manufactured by the company, under the following conditions:
WIRING DIAGRAM FOR AN OPERATOR WITH TIMER AND THE LOCK CONNECTOR ON THE 1. Repair and readjustment of equipment may only be carried out by PPA Technical Assistance,
CONTROL BOARD
which is qualified to open, remove, and substitute parts or components, as well as repair
defects covered by this warranty; thus, failure on observing this guideline and the verified use
of any non-original parts will cause the resignation of this warranty on the part of the user;
2. The warranty will not extend to accessories such as cables, screw kit, fixing brackets, power
supplies etc.; BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
3. Expenses for packaging, transportation and product reinstallation will be sole responsibility
of the consumer;
4. The equipment must be sent directly to the Company responsible for the sale (manufacturer's
PPA RELAY MODULE
representative), through the address contained in the purchase invoice, properly packed, thus
avoiding loss of the warranty;
5. Within the additional period of 275 days, visits and transportation in places where authorized
technical assistance is not available will be charged. The cost of transportation of the product
127 VAC
and/or technician will be sole responsibility of the consumer and
OR
LOCK CONNECTOR
220 VAC
6. The substitution or repair of the product does not prolong the warranty time.
OPERATOR'S CONTROL
According to the
BOARD
electromagnetic lock voltage.
This warranty will be terminated if the product:
1. Is damaged by natural agents, such as atmospheric discharges, floods, wildfires, landslides
WIRING DIAGRAM FOR AN OPERATOR WITH TWO LOCKS, TIMER AND LOCK CONNECTOR
etc.;
ON THE CONTROL BOARD
2. Is installed in an improper electric power supply or if it is not according to any of the
installation instructions displayed on the manual;
3. Shows defects caused by droppings, collisions or any other physical accident;
4. Shows signs of product violation or attempted repair by unauthorized personnel;
5. Is not used for its intended purpose;
6. Is not used under normal conditions;
7. Is damaged by accessories or equipment connected to it.
Recommendation:
We recommend that both the installation and the maintenance of the operator to be performed
by an authorized PPA technical service. If the product fails or has an improper operation, seek
an Authorized Technical Service to fix it.
LOCK CONNECTOR
OPERATOR'S CONTROL
BOARD
TIMER BOARD
CLOSING
OPENING
COMMON
SINGLE-PHASE
INDUCTION MOTOR
TIMER BOARD
NOTE:
RELAY MODULE is sold
separately.
TIMER BOARD
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
PPA RELAY MODULE
127 VAC
NOTE:
OR
RELAY MODULE is
220 VAC
sold separately.
According to the
electromagnetic lock voltage.
TIMER BOARD
CLOSING
OPENING
COMMON
SINGLE-PHASE
INDUCTION MOTOR
TIMER BOARD
NOTE:
RELAY MODULE is sold
separately.
TIMER BOARD
BLACK WIRE AND WHITE WIRE = 127 V
BLACK WIRE AND RED WIRE = 220 V
PPA RELAY MODULE
127 VAC NOTE:
OR
RELAY MODULE is
220 VAC
sold separately.
According to the
electromagnetic lock voltage.
The PPA
The PPA
The PPA
The PPA