Ryobi A90CM03 Manual De Instrucciones

MULTI-PRO ROTARY CHUCK
A90CM03
For use with PRT100, PCL480, PBLRT01, TVM01, FVM51,
RRT100, and RRT200 Rotary Tools.
WARNING!
To reduce the risk of injury, user must read and understand the
operator's manual for their rotary tool and this instruction sheet.
Always wear eye protection with side shields marked to com-
ply with ANSI Z87.1. Ensure compatibility and fit before using
this accessory. Do not use this accessory if a part is damaged
or missing. If you are not comfortable performing any of the
functions described in these instructions, take your unit to an
authorized service center.
WARNING:
Never install, remove, or adjust any attachment while rotary tool
is running. Failure to stop the motor can cause serious personal
injury. Never operate rotary tool without an attachment head or
the collar installed.
NOTE: Follow all guidelines and warnings in your rotary tool
operator's manual.
The multi-pro rotary chuck allows you to hand-tighten or release the
accessory in the chuck jaws. The chuck is machined to precision
tolerances to fit accessories with 1/32 to 1/8 in. diameter shanks.
INSTALLING THE MULTI-PRO ROTARY
CHUCK
See Figure 1.
 Verify the rotary tool switch is in the OFF (O) position and
unplug the rotary tool or remove the battery pack, if applicable.
 Engage the spindle lock and remove accessories and quick-
change collet according to the rotary tool operator's manual.
 Depress and hold the spindle lock button and rotate the shaft
by hand until the spindle lock engages the shaft, preventing
further rotation.
 Place the multi-pro rotary chuck on the shaft and begin threading
on by hand until there is resistance.
 Use the 3/8 in. wrench included with your rotary tool on the
bottom threaded end of the chuck and rotate clockwise until
tightly secured.
NOTE: If sleeve cannot be tightened or loosened sufficiently
by hand, use the included 3/8 in. chuck wrench on the bottom
threaded end of the chuck. Turn clockwise to tighten or
counterclockwise to loosen.
 To remove the chuck, engage the spindle lock. Place the 3/8
in. wrench included with your rotary tool on the bottom threaded
end of the chuck and turn counterclockwise to loosen. Continue
turning counterclockwise to remove the chuck from the tool.
INSTALLING/REMOVING ACCESSORIES
See Figure 2.
 Verify the rotary tool switch is in the OFF (O) position and
unplug the rotary tool or remove the battery pack, if applicable.
 Choose an accessory that fits the multi-pro rotary chuck and
is suitable for the application you are attempting.
998000895
3-17-22 (REV:02)
 While depressing the spindle lock, use your hand to loosen
the chuck by rotating the sleeve counterclockwise.
 Insert the shank of the accessory into the chuck until the shank
bottoms out, then pull it out 1/16 in. to allow for expansion
when the accessory gets hot.
 Rotate the chuck sleeve clockwise to tighten.
 To remove the accessory, engage the spindle lock, loosen
the chuck, and remove the accessory.
NOTE: It is normal for the chuck to unthread from the tool as
it is loosened. If necessary, re-thread the chuck.
Fig. 1
D
A
A - Multi-pro rotary chuck (mandrin rotatif multi-pro, portabrocas rotatorio
multi-pro)
B - Shaft (arbre, eje)
C - Spindle lock button (bouton de blocage de la broche, botón de bloqueo
del husillo)
D - Threaded end (extrémité filetée, extremo roscado)
E - Loosen (desserrer, aflojar)
F - Tighten (serrer, apretar)
Fig. 2
A - Accessory (accessoire, accesorio)
B - Loosen (desserrer, aflojar)
C - Tighten (serrer, apretar)
TTI CONSUMER POWER TOOLS, INC.
P.O. Box 1288, Anderson, SC 29622
Phone 1-800-525-2579
www.ryobitools.com
C
C
B
F
E
C
B
A