Idiomas disponibles
Idiomas disponibles
ATTACHING THE STORAGE FOOT (FIG. 6)
1.
With stand right side up, place the storage foot (C) over the
indentations of the wheel and storage-foot connector (D) so
when the stand is right side up the storage foot will angle
upward.
2.
Turn stand upside down and align the holes in storage foot
and storage foot connector. Install two M8 x 15 mm button
head screws (K) with curved washers at (M) to attach storage
foot and the connector.
3.
Tighten screws securely with the supplied hex wrench.
4.
Securely tighten the storage-foot connector screws that were
loosely installed in Attaching the Wheel and Storage Foot
Connector.
TO RAISE AND LOWER THE STAND (FIG. 1, 7)
The stand has three positions: Closed, Fully extended and
Intermediate.
1.
Turn the stand right side up on the floor.
IMPORTANT: Stand must be right side up when cutting white
cable ties (S).
2.
Use wire cutting pliers to cut the white cable ties (S) shown in
figure 1.
IMPORTANT: DO NOT cut the black cable ties securing the
cables that open the stand.
3.
Place your right foot on the bottom of the extension leg (B).
4.
Grasp the handle (F) with both hands.
5.
Use the thumb of your left hand to push down on the red
activating lever (X). This disengages the latching mechanism.
6.
To reach the intermediate position: Lift up on the handle
and slowly raise the stand. The stand will stop at the
intermediate position. Release the lever.
NOTE: When in the intermediate position, the stand will lower
slightly when a tool is placed on it. The intermediate position
does not lock against upward motion. The stand relies on the
weight of the tool to remain in the intermediate position.
7.
To fully extended stand: Start in the intermediate position.
Repeat STEPS 3-5. Lift up on the handle and raise the stand
to the fully extended position. The stand will latch in the fully
extended position. Release the lever.
8.
To close stand: Repeat STEPS 3-5. Lift up on the handle and
push down until the stand is closed. Release the lever.
ATTACHING THE EXTENSION WORK SUPPORTS
(FIG. 8, 9)
IMPORTANT: Be sure the longer side of the "T" in the work
support arm (I) is oriented down as shown in Figure 8. Ensure the
arrow on the label points down.
1.
Insert the work support arm (I, Fig. 9) with the small black cap
(inset, Fig. 9) into the hole (Y) of the stand closest to the red
activating lever. Push the arm in to lock in place.
2.
Repeat for other work support arm on opposite end. Push the
arm in to lock in place.
3.
With the stand raised to desired height, place the top
piece (E1) of the extension work support into the top of
the work support arm (I) hole. Insert the bottom piece (E2)
of the extension work support into the bottom hole of the
work support arm, with proper orientation to the top piece.
NOTE: Ensure the slanted side of the extension work support
(E1) is positioned inward as shown in Figure 8).
4.
Tighten the vertical lock knob (Z).
5.
Repeat with the other extension work support.
NOTE: The internal locking mechanism keeps the work supports
from disengaging.
ATTACHING THE CORD WRAPS (FIG. 10, 11)
NOTE: Place the cord wraps (J, Fig. 10) in opposite positions to
hold the cord securely.
1.
Place the cord wrap (J) screw into the hole (BB) from outside
of stand. Place the washer (CC) and nut (DD) on cord wrap
screw and finger tighten nut.
2.
Using a crescent wrench or 1/2 inch open end wrench, tighten
the screw securely.
3.
Repeat for the other cord wrap.
6
C
D
7
8
E1
10
J
12
FF
4-ENG
K, M
F
X
B
9
E
I
I
E2
Z
BB
J
11
EE
GG
FF
EE
Y
DD
CC
