Idiomas disponibles
Idiomas disponibles
2. Move the adjustable fence to the inner position,
towards the blade. The maximum distance
between the adjustable fence (35) and the saw
blade (6) is 8mm, as shown on figure J. Make
sure the fence does not touch the blade.
3. Firmly clamp the workpiece;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so that
the saw blade cuts through the piece of work
and passes through the slot in the table. Do not
put undue pressure on the saw, let the machine
do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a bevel cut (fig. L, M)
Follow these steps to make an angled cut to the
edge of the wood:
1. Adjust the mitre angle to 0° and the bevel angle
to the desired position ;
2. Move the adjustable fence to the outer position,
away from the blade. The maximum distance
between the adjustable fence (35) and the saw
blade (6) is 8mm, as shown on figure M. Make
sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the work-
piece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so that
the saw blade cuts through the piece of work
and passes through the slot in the table. Do not
put undue pressure on the saw, let the machine
do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a compound cut (fig. M, N)
Follow these steps to make a combination of mitre
and bevel cut:
1. Adjust the mitre angle and the bevel angle to
the desired position ;
2. Move the adjustable fence to the outer position,
away from the blade. The maximum distance
between the adjustable fence (35) and the saw
blade (6) is 8mm, as shown on figure M. Make
sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the work-
piece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
WWW.VONROC.COM
blade has reached full speed;
5. Now bring the handle slowly downwards so that
the saw blade cuts through the piece of work
and passes through the slot in the table. Do not
put undue pressure on the saw, let the machine
do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Using the slide function
For extra wide workpieces, the machine is equipped
with a sliding function. When using the slide function,
make sure to loosen the locking bolt for slide rails
(29). Pull the handle (2) away from the fence (9) until
the saw blade is in front of the workpiece. Slowly
guide the tool arm downwards using the handle and
afterwards push the handle (2) towards the fence (9)
and saw through the workpiece with uniform feed.
For small workpieces, it is possible to fix the sliding
function in the rear position of the saw with the
locking bolt for slide rails (29). If more cutting
width is desired, then it is necessary to loosen the
locking bolt for slide rails (29).
Using the length stop (Fig. O)
The length stop (8) on both the left and right table
extensions (10) can be used for easily sawing
workpieces to the same length.
1. Move the length stop (8) upwards;
2. Loosen the locking bolt for table extension (34);
3. Adjust the table extension (10) to the required
length.
4. Tighten the locking bolt for table extension (34).
Adjusting the depth stop (Fig. P)
The depth stop can be adjusted, to limit the cutting
depth. This can be used to easily saw a groove. To
do so:
1. Loosen the knurled nut for depth adjustment
(45);
2. Adjust the knob for depth adjustment (24) to
the desired depth;
3. Tighten the knurled nut for depth adjustment (45).
Switching the laser on/off (Fig. B)
Press the laser switch (46) to switch the laser on
or off. The laser switch (46) also turns on the LED
worklight.
EN
17
