TrolMaster Tent-X TCS-1 Manual De Instrucciones página 4

Line 1 Lighting Setting On this page, you can create your light
settings. Use the UP and DOWN buttons to
Mode LED
navigate the options on this page and press
Power 100%
ENTER on an item to change it. When you see
On at 20:00
the item blinking, use the arrows to switch
Off at
08:00
Dim at o
84 F between the selections. When you have
o
Stop at 89 F
selected your item, press ENTER again to
Sun R/S time OFF
confirm the selection. Select whether you're
using HID or LED lights. You can also select the On/Off time for your
lights, the temperature at which the lights will dim, the Sunrise and Sunset
time, and more.
Devices:
Devices Setting
The Devices tab is where you will set up your
climate control and irrigation devices. With
T1 T2
Heat Cool
the use of our plug-in DS modules, you can
H1 H2
connect and control the devices via the
Humid Dehumid
controller. Each type of DS module has a
C1 C2
specific function. The DST module can only
In Out
control temperature devices, the DSH module
P1 P2 P3 P4
can only control humidity devices, the DSC
module can only control CO2 devices, and the DSP module is a multi-func-
tion module that works as a timer. Go to trolmaster.com for more
information.
Press ENTER to access the device settings. You can set up 2 climate
control devices each for temperature, humidity, and CO2 on each of the 2
columns. You can also set 4 program devices, labeled from P1 to P4. This is
where you can link your irrigation or more climate devices to the Tent-X.
*
If you are using more than two devices in your grow tent, you can plug in
a Y-splitter into the device port and plug in a device into one of the ports
on the Y-splitter and plug in another Y-splitter into the second port, you
can keep repeating this procedure to create a daisy-chain connection to
the Tent-X in order to connect multiple devices. If you'd like a "cleaner"
setup, you can use TrolMaster's 8-port splitter hub (SPH1) to connect
multiple devices to the Tent-X.
06
EC Fan:
In the Tent-X system, EC Fans can be
Setting
Setting
controlled via the EFC-1 control adaptors.
Day & Night Users can control two EC fans at the same
time, categorized as F1 and F2. The first fan,
Climate
F1, can be used and controlled as an exhaust
Light Devices fan to control temperature and humidity. The
second fan, F2, can be used and controlled as
EC Fan System
an intake fan to create a desired negative
pressure in the grow tent.
Using the EFC-1 control adaptors, you can control 0-10-volt or
PWM-type EC fans, which you can select when first setting up the EFC-1.
The EFC-1 control adaptors can control the speed of the exhaust fan and
the intake fan, which as a result, can manipulate the temperature, humidity
and negative pressure inside the grow tent to suit the users' desired
outcome.
First, plug in the Y-splitter that comes with your Tent-X. You then need to
plug two EFC-1 adaptors into the Y splitter RJ12 ports. Next, plug your
fans into the RJ12 port opening of the EFC-1 adaptors. Finally, address
each fan on the adaptors and establish the designated Intake and Exhaust
fans.
F1:
F1: There are 4 modes for the F1 fan. These 4
Setting
Setting
modes include:
Cool only mode: The exhaust fan is only
Temp
Exhaust Fan
2 2
controlled by the temperature in the grow
(F1)
Humid
tent
Dehu only mode: The exhaust fan is only
Intake Fan
controlled by the humidity levels in the grow
(F2)
tent
Cool priority mode: The exhaust fan is controlled by both temperature
and humidity, however, it will prioritize temperature to be within the
defined range if both can't be achieved.
Dehu Priority mode: The exhaust fan is controlled by both temperature
and humidity, however, it will prioritize humidity to be within the defined
range if both can't be achieved.
On the F1 page, you also have to set the minimum and maximum fan
speed the exhaust fan can operate at.
CO2 Interlock:
The CO2 interlock function is a powerful tool to preserve your CO2
supply. When the CO2 interlock function is toggled on, CO2 will not be
injected into the grow tent when the fans are activated.
07