Idiomas disponibles
Idiomas disponibles
Mounting/replacing the accessory
WARNING: Disconnect battery pack from oscillating
tool or place the switch in the locked or off position
before making any assembly, adjustments or changing
accessories.
Such preventive
safety measures reduce the risk
of starting the tool accidentally.
Note:
An adapter is provided
GB
to enable the use of Dremel
accessories on this tool.
5MM
Installing and removing
HEX WRENCH
accessories
•
To mount the tool accessory,
remove the centre assy screw
and outer washer with the
allen key provided.
Locate the accessory on the
accessory holder by locating
the 4 pins of the accessory
holder through the location
holes in the accessory.
Ensure the accessory is sitting flat on the accessory
holder after the accessory has been located.
Note. The accessory can be orientated in one of 6 positions
on the accessory holder, 60º apart.
•
Locate the washer on the
accessory and fit the clamping
screw through the washer
and accessory and into the
accessory holder. Use the hex
screw to fasten the application
tool/accessory. Tightly fasten
the screw with the Allen key.
Note.
Ensure the washer is fitted
and located under the head of the screw.
•
Check the tight seating of the application tool/accessory.
Incorrect or not securely fastened application tool/
accessory can come loose during operation and pose
a hazard. Do not use the tool without the clamping
washer under the head of the accessory clamping screw.
•
For removing the application tool/accessory, loosen the
screw with Allen key and remove the screw, washer and
accessory from the tool.
ADAPTER
Note:
some accessories, such as scrapers or blades, may
be mounted either straight on the tool or at an angle to
enhance usability.
HEX
BOLT
Installing sanding papers
•
The sanding plate is fitted with Velcro backing for
quick and easy fastening of sanding paper with Velcro
adhesion.
•
Before attaching the sanding sheet, free the Velcro
backing of the sanding plate from any debris by tapping
against it in order to enable optimum adhesion.
•
Position the sanding paper flush alongside one edge of
the sanding plate, then lay the sanding paper onto the
sanding plate and press it against it with a light turning
motion in clockwise direction.
•
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding paper match with the holes
in the sanding plate.
•
To remove the sanding paper, grasp it at one of the tips
and pull it off from the sanding plate.
•
Sanding accessories, such as fleece pads/ polishing
cloth pads, are attached to the sanding plate in the
same manner.
•
After considerable service the backing pad surface
16
will become worn, and the backing pad must be
replaced when it no longer offers a firm grip. If you are
experiencing premature wear out of the backing pad
facing, decrease the amount of pressure you are applying
during operating the tool. For maximum use of abrasive,
rotate pad 120 degrees when tip of abrasive becomes worn.
Operation
Intended use
This tool is intended for the sawing and cutting wooden
materials, plastic, gypsum, non-ferrous metals and fastening
elements (e.g. nails, staples). It is also suitable for working
soft wall tiles as well as for dry sanding and scraping of
small surfaces. It is especially suitable for working close to
edges and for flush cutting.
Starting operation
Inserting the battery pack
(see above fitting and remove battery pack).
Use only original Lithium-ion battery pack with the voltage
on the nameplate of your tool. Using other batteries can
lead to injuries and pose a fire hazard.
Note.
Use of batteries not suitable for the tool can lead to
malfunctions of or cause damage to the tool.
Insert the battery pack into the handle until it can be felt to
engage and faces flush against the handle.
Switching On and Off
To start the tool, slide the On/Off
switch 1 forward so that the "I" is
indicated on the switch.
To switch off the tool, slide the
On/Off switch 1 toward the rear
so that the "0" is indicated on the
switch.
The Li-ion battery is protected against deep discharging
by the "Electronic Cell Protection circuit". When the battery
is empty, the tool is switched off by means of a protective
circuit, the tool no longer rotates.
Note:
The tool should automatically switch off because of
a discharged or overheated battery, make sure to set the
tool's On/Off switch 1 to off position. Charge the battery and
allow it to cool down before restarting the tool. Otherwise
the battery can become damaged.
Variable speed
control thumbwheel
This tool is equipped with
a variable speed control
thumbwheel 5, the speed may
be controlled during operation by
presetting the thumbwheel in any
one of five positions.
Temperature and overload
protection
This tool is fitted with electronic overload and temperature
protection.
If the tool is forced and overloaded, the tool will stop
operation. Further more, if the tool is used continually close
to the overload point, the tool and the cells could over
heat, so again, the tool will stop operation if the cell or tool
temperature exceed a pre determined temperature.
To reset
If the tool is overloaded, switch the tool off. This has reset
the tool. To start, slide the on / off switch forward to the "I"
position and the tool will resume operation.
Note.
Reduce the pressure on the tool and allow the
accessory to do the work so the repeat of overload will
not happen.
If the tool has stopped due to overheating, then the switch
needs to be turned OFF and the too and battery pack
allowed to cool.. This may take several minutes, but the tool
will not restart until the cells have cooled.
Note.
Do Not force cool the battery pack.
Low voltage cut out
The battery pack used on this tool is fitted with a low voltage
cut out feature within the circuitry.
The low voltage cut out feature operates when the voltage
drops below a pre set value. This feature automatically
17
GB
