Practical Tips; Replacing The Power Cable; Cleaning & Maintenance - WorkPro W124746A Manual De Instrucciones Original

the recesses in the plug-in tool.The tool chuck (2) is
magnetic in order to secure the plug-in tool during
the clamping procedure.
Close the quick-release lock for changing tools (4)

again. Take care that the pins of the chuck (2)remain
in the recesses in the plug-in tool.
Warning!
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate (Fig.4)
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
Follow the directions for attaching the accessories

to attach the sanding plate to the tool.
Align the sanding sheet with the sanding plate and

use your hand to press it firmly on the sanding plate.
Press the sanding sheet firmly against a smooth

surface for a short period, and then switch on the
tool. The burr will form a non-slip bond with the
outer edge of the sanding sheet felt. (Fig.4)
If one point has become worn, peel off the sanding

sheet, turn it 120° and attach it on again.
6. Operation
Warning!
Check the voltage! The voltage must comply with
the information on the rating label!
6.1 Switching on/off (Fig. 5)
Make sure the ON/OFF switch (1) is in its OFF

position. Connect the plug with a suitable socket.
Your product is now ready to be used.
To turn the tool ON, push the ON/OFF switch

forward. To turn it OFF, push the switch backward.
(Fig.5).

6.2 Practical tips

Switch on the equipment.

Work away from the body.

Never move your hands into the direct vicinity of the

work area.
Use only plug-in tools which are in good working

order and undamaged.
Plug-in tools
Sawing: Sawing wood and plastic.
GB
Notes on working practice: When sawing, watch out
for foreign bodies in the workpiece and remove these
if necessary. Plunge cutting is allowed only in soft
materials such as wood or plaster- board.
Sanding/grinding: Surface sanding/grinding at edges,
in corners or hard-to-reach areas. Depending on
choice of sanding/grinding
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment offers
particularly high performance for the sanding/ grinding
of hard-to-reach corners and edges. To sand/grind
profiles and channels you can also work with just the
tip or the edge of the sanding/ grinding disk. Various
sanding/grinding papers are available, specially
designed for the different types of material you may be
working on and the amount you wish to remove from
the surface.
The amount removed will depend largely on the choice
of sanding/grinding paper and pressure applied to the
sanding/grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with a flat
angle of incidence and little pressure. The surface (e.g.
wood, plaster) may be damaged if too much pressure
is used.
6.3 Speed control (Fig. 6)
The speed dial (3) is numbered "MIN" through "MAX",
with position "MIN" being the lowest speed and
position "MAX" being the highest speed. (Fig.6)

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-sales
service or similarly trained personnel to avoid danger.
8. Cleaning, maintenance
Danger!
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with
compressed air at low pressure.
We recommend that you clean the device immedi-

ately each time you have finished using it.
Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or
7
paper for the