Recording A Sync Signal On The Tape - Yamaha MT400 Manual De Instrucciones

40

Recording a SYNC Signal on the Tape

8
2
1
Connect the MT400 to the FSK/MIDI
converter or the SMPTE/MTC converter as
shown in the diagrams on pages 38 and 39.
2
Set the [INPUT-FLIP] switch on Input Channel
4 to "MIC/LINE (
3
Set the [REC SELECT] switch on Track 4 to
" ".
4
The Track 4 REC SELECT indicator flashes. A signal
output from the converter is routed to Track 4 via the
MIC/LINE INPUT 4 of the MT400.
4
Set the [METER SELECT] switch to "
5
Press the [PAUSE] button, then the
button.
REC
6
Prepare the MIDI sequencer and FSK/MIDI or
SMPTE/MIDI converter for SYNC signal
output.
—Owner's Manual
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE TAPE TAPE TAPE
LINE LINE LINE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
".
4TR
STEREO INPUT
5 6 7 8
L R L R
1 2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
– +
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
5
7
Start the MIDI sequencer, or SMPTE/MTC
converter.
A SYNC signal is sent from the converter to Track 4
via Input Channel 4.
8
While checking the level meter, use the GAIN
control and the fader on Input Channel 4 to
set the level of the SYNC signal.
At this time, set all the EQ controls to midway around
noon (flat).
Note: If the level of the SYNC signal is too high, the
signal may sometimes leak to an adjacent track. If the
level is too low, you may not be able to achieve
correct synchronization. Set the level so that the 0 dB
segment of the level meter lights up.
+6
POWER
+3
0
–5
–10
3 4
3
METER SELECT
4
4 4TR
OFF STEREO
R
0
FF STOP PAUSE
C A