Idiomas disponibles
Idiomas disponibles
Chiseling and Chipping
These MILWAUKEE Hammers may be used for
chipping and chiseling.
When chiseling, hold the tool at an angle to the
workpiece. Work from a corner or close to the edge
of the workpiece, breaking off one small area at a
time rather than attempting too large an area.
A variety of accessories are available.
Bushing Tools-Used to surface
concrete.
Mortar Cutting Chisels (Seam
Tools)-For removing old mortar for
tuck pointing or caulking.
Bull Points-For demolition work
and starting holes in concrete slabs.
Flat Chisels-For edging, chipping
or channeling.
Scaling Chisels-For removing
weld spatter or scale and cutting
straight lines.
Slotting Chisel-For slotting and
cutting between drilled holes in
concrete and masonry.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the tool before performing
any maintenance. Never disassemble the tool.
Contact a MILWAUKEE service facility for ALL
repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular
maintenance program. Inspect your tool for issues
such as undue noise, misalignment or binding of
moving parts, breakage of parts, or any other condi-
tion that may affect the tool operation. Return the tool
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool to a MILWAUKEE service facility for inspection.
Maintaining Hammer Chisels
Through normal use, the shank of the chisel can
"mushroom" over and cause the chisel to become
stuck inside the hammer. To prevent this from hap-
pening, periodically remove the chisel from the tool
and inspect the shank. If the shank starts to "mush-
room", have the chisel refurbished or replaced.
Brush Replacement
These MILWAUKEE hammers are will automatically
shut off when the brushes need to be replaced. Re-
turn your tool to the nearest MILWAUKEE service
facility for repairs.
Service Indicator Light
These MILWAUKEE Hammers feature a service
indicator light. When the red light turns on, the tool is
in need of servicing. Return your tool to the nearest
MILWAUKEE service facility for service.
NOTE: When the service light comes on, the tool will
continue to run for a few hours and then the motor
will shut off.
To reduce the risk of personal in-
WARNING
jury, electric shock and damage,
never immerse your tool in liquid or allow a liquid
to flow inside it.
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
Thick Wall Carbide-Tipped Core Bits
Core Body with Guide Plate and Centering Pin
Cat. No.
48-20-5125
48-20-5130
48-20-5135
48-20-5140
48-20-5145
48-20-5150
48-20-5155
48-20-5160
48-20-5165
NOTE: Use MILWAUKEE core bits Cat. No.
48-20-5125 through 48-20-5165. Do not use LHS
(Large Hole System) Components with rotary ham-
mers 5340-20 and 5342-20. The bits could fail,
breaking apart at the threaded stud and causing
injury and property damage.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
9
Cleaning
Repairs
Diameter
Drilling Depth
1-1/2"
4-1/16"
1-3/4"
4-1/16"
2"
4-1/16"
2-1/2"
4-1/16"
3"
4-1/16"
3-1/2"
4-1/16"
4"
4-1/16"
5"
4-1/16"
6"
4-1/16"
(1.800.729.3878)
