Intended Use; Technical Data; Before Starting The Equipment - EINHELL TE-RS 18 Li Manual De Instrucciones

3. Intended use

The machine is designed for the grinding/sanding
of wood, metal, plastic and similar materials using
the appropriate grinding/sanding paper. The
equipment is not suitable for wet sanding.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ........................... 18 V
Idling speed: ................. 7000-11000 RPM (min
Sanding/grinding area: ................ Ø 5'' (127 mm)
Abrasive paper size (Hook-and-loop fastener): ...
...................................................... Ø 5'' (127 mm)
Weight: ....................................... 2.65 lbs (1.2 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's con-struction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
Anl_TE_RS_18_Li_USA_SPK7.indb 11 Anl_TE_RS_18_Li_USA_SPK7.indb 11
EN
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
An empty battery pack requires a charging
)
-1
period of approximately 0.5 to 1 hour.
5.1 Fitting the dust extractor adapter (Fig. 2/
Item 2)
Plug the dust extractor adapter (2) onto the
vacuum cleaner connector as shown in Fig. 2.
Connect the dust extractor adapter to a suitable
dust extraction system.
5.2 Fitting the dust bag (Fig. 3/Item 4)
•
Fit the dust bag (4) to the vacuum cleaner
adapter (2) by turning it slightly as far as the
notch will go as shown in Fig. 3.
•
The dust is extracted directly into the dust
bag (4) through the abrasive paper and the
orbital plate (5).
•
To remove the dust bag again, pull and twist
it off.
Caution!
For health reasons it is imperative that you use
the dust bag or a dust extraction system.
5.3 Fastening the abrasive paper with the
Hook-and-loop fastener system (Fig. 4)
•
Only use abrasive paper with the
corresponding dimensions and matching
perforations.
•
Place the abrasive paper onto the orbital
plate (4) as shown in Fig. 5. Make sure
- 11 -
26.04.2022 15:05:32 26.04.2022 15:05:32