Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

H-9823, H-9824
H-9825, H-9826
TOP-TRACK SHELVING
TOOL NEEDED
Rubber Mallet
Phillips Screwdriver
63" Post
(x 8 for H-9823, H-9824)
(x 12 for H-9825, H-9826)
Shelf (60 x 24", 72 x 24")
(x 16 for H-9823, H-9824)
(x 20 for H-9825, H-9826)
STATIONARY UNITS
1.
Stationary units use two 72" posts and two 69" posts.
72" posts must be on the same side lengthwise, and
the 69" posts on the opposite side lengthwise.
(See Figure 1)
NOTE: Self-leveling feet should be turned to
lowest setting.
Figure 1
69" Posts
PAGE 1 OF 15
1-800-295-5510
uline.com
PARTS
69" Post x 4
Shelf Support
(x 64 for H-9823, H-9824)
(x 80 for H-9825, H-9826)
SHELVING ASSEMBLY
72" Posts
Pour le français, consulter les pages 11-15.
Caster
(x 8 for H-9823, H-9824)
(x 12 for H-9825, H-9826)
2. Starting with the lowest shelf, snap the interlocking
pieces of a shelf support (wide end down) around
the post at the lowest groove where shelf is to be
located. Slide the support up or down until it snaps
into the groove. Add a shelf support to the same
height on the remaining posts. (See Figure 2)
Figure 2
Para Español, vea páginas 6-10.
72" Post x 4
Self-Leveling Foot x 8
Shelf
Support
0222 IH-9823
Tabla de contenido
loading

Resumen de contenidos para Uline H-9823

  • Página 6 Mazo de Caucho Desarmador de Cruz PARTES Postes de 63" 4 Postes de 69” 4 Postes de 72” (8 para H-9823, H-9824) (12 para H-9825, H-9826) Repisa (60 x 24", 72 x 24") Soporte para Repisa Ruedas 8 Patas Autoniveladoras...
  • Página 7: Continuación Del Ensamble De Estantería

    CONTINUACIÓN DEL ENSAMBLE DE ESTANTERÍA 3. Deslice los postes a través de la parte inferior de la 5. Determine la altura de la repisa hasta que la misma se deslice firmemente siguiente repisa, trabe los sobre los soportes. (Vea Diagrama 3) soportes para repisa, luego agregue la repisa y asegúrela.
  • Página 8: Ensamble Del Riel

    ENSAMBLE DEL RIEL RIEL POSTERIOR RIEL FRONTAL 1. Coloque las tres piezas del riel posterior en línea. 1. Coloque las tres piezas del riel frontal en línea. (Vea Diagrama 7) (Vea Diagrama 10) NOTA: El riel frontal sin conector debe colocarse a la izquierda.
  • Página 9: Continuación Del Ensamble Del Riel

    PARTES DEL ASA 2 Barras para Asas 2 Asas Resorte Tornillo para Asa Rondana de Seguridad (2 para H-9823, H-9824) (2 para H-9823, H-9824) (4 para H-9823, H-9824) (4 para H-9823, H-9824) (4 para H-9823, H-9824) (3 para H-9825, H-9826)
  • Página 10: Continuación Del Ensamble Del Asa

    Estos deben apuntar hacia el suelo. Diagrama 17 Ensamble Terminado 4. Empuje el asa dentro de los orificios de la barra para asa. (Vea Diagramas 18-19) Diagrama 19 Diagrama 18 800-295-5510 uline.mx PAGE 10 OF 15 0222 IH-9823...

Este manual también es adecuado para:

H-9824H-9825H-9826

Tabla de contenido