Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
8. Measure the vertical distance between
9. If your measurement is greater than the Allowable
Distance Between
b
Distance Between Walls in the following table, the laser
must be serviced at an authorized service center.
Distance Between
and
a
30'
40'
50'
Distance Between
and
a
9.0 m
12.0 m
15.0 m
Horizontal Beam - Pitch Direction
(Fig. A, K, L, M)
Checking the horizontal pitch calibration of the laser requires
a single wall at least 30' (9 m) long. It is important to conduct
a calibration check using a distance no shorter than the
distance of the applications for which the tool will be used.
1. Place the laser against the end of the wall on a smooth,
flat, stable surface that is level in both directions
(Figure K).
2. Move the Power/Transport Lock switch
turn the laser ON (Figure A).
3. Press button to turn on the horizontal beam
4. At least 30' (9 m) apart along the laser beam, mark
and
b
.
5. Move the laser to the opposite end of the wall (Figure L).
6. Position the laser toward the first end of the same wall
and parallel to the adjacent wall.
7. Adjust the height of the laser so the center of the beam is
aligned with
b
.
8. Directly above or below
(Figure M).
9. Measure the distance between
10. If your measurement is greater than the Allowable
Distance Between
a
and
Distance Between Walls in the following table, the laser
must be serviced at an authorized service center.
Distance Between
and
a
30'
40'
50'
Distance Between
and
a
9.0 m
12.0 m
15.0 m
Vertical Beam (Fig. A, N)
Checking the vertical (plumb) calibration of the laser can be
most accurately done when there is a substantial amount of
vertical height available, ideally 20' (6 m), with one person
12
b
and
and
c
for the corresponding
Allowable Distance Between
b
and
c
b
1/4"
5/16"
13/32"
Allowable Distance Between
b
and
b
c
6.2 mm
8.3 mm
10.4 mm
1
to the right to
4
a
, mark
c
along the laser beam
a
and
c
.
c
for the corresponding
Allowable Distance Between
b
and
a
c
1/4"
5/16"
13/32"
Allowable Distance Between
b
and
c
a
6.2 mm
8.3 mm
10.4 mm
c
.
on the floor positioning the laser and another person near
a ceiling to mark the position of the beam. It is important
to conduct a calibration check using a distance no shorter
than the distance of the applications for which the tool will
be used.
1. Place the laser on a smooth, flat, stable surface that is
level in both directions (Figure N1).
2. Move the Power/Transport Lock switch
turn the laser ON (Figure A).
3. Press the buttons to turn on both vertical beams
4. Mark two short lines where the beams cross
also on the ceiling
beam's thickness (Figure N2).
5. Pick up and rotate the laser 180º, and position it so
the beams line up with the marked lines on the level
surface
6. Mark two short lines where the beams cross on the
ceiling
7. Measure the distance between each set of marked lines
on the ceiling (
greater than the values shown below, the laser must be
serviced at an authorized service center.
Ceiling Height
.
a
Ceiling Height
90º Accuracy Between Vertical Beams
(Fig. A, O)
Checking 90º accuracy requires an open floor area at least 33'
x 18' (10 m x 5 m). Refer to Figure O for the position of the
laser at each step and for the location of the marks made at
each step. Always mark the center of the beam's thickness.
Place the laser on a smooth, flat, stable surface that is level in
both directions.
1. Move the Power/Transport Lock switch
turn the laser ON (Figure A).
2. Press button to turn on the side vertical beam
3. Mark the center of the beam at three locations
(
a
,
b
should be at the midpoint of the laser line (Figure O1).
4. Pick up and move the laser to
5. Press
6
(Figure O2).
6. Position the front vertical beam so it crosses precisely
at
b
, with the side beam aligned with
c
,
d
. Always mark the center of the
e
, f (Figure N3).
g
,
h
.
c
,
g
and
d
,
h
Allowable Distance Between
8'
10'
14'
18'
30'
Allowable Distance Between
2.5 m
3.0 m
4.0 m
6.0 m
9.0 m
,
c
) on the floor along the side laser line. Mark
b
to turn on the front vertical beam too
1
to the right to
5
6
.
a
,
b
and
). If the measurement is
Marks
1/16"
3/32"
1/8"
5/32"
1/4"
Marks
1.7 mm
2.1 mm
2.8 mm
4.1 mm
6.2 mm
1
to the right to
6
.
b
.
c
(Figure O2).
Tabla de contenido
