Tabla de contenido
Idiomas disponibles
Idiomas disponibles
O-Ring Maintenance
Purchasean O-Ring Repair Kit,item7175116, at your local
Searsor by calling 1-800-4-1VlY-NOIVlE (469-4663) or online at
www.sears.com. It is not included with the pressurewasher.
This kit includesreplacemento-rings and a water inletfilter.
Referto the instruction sheet providedin the kit to serviceyour
unit's o-rings.
,& WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
= NEVER repairleakingconnections with sealant o f any kind.
Replace o-ring or seal.
ENGINEMAINTENANCE
,A WARNING Unintentional sparking could cause fire or
"_lh.
electric shock resulting in death or
serious injury.
WHEN ADJUSTING ORMAKING REPAIRS TOYOUR PRESSURE
WASHER
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTINGFOR ENGINESPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptableif classified for service SF, SG,
SH, SJ or higher. DONOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
oF
104 _
_
__
86
6850 _ COm_:nO
32
2
14
-4
-22
°C
•
40
__
30
=,_20
10
_
---0
-----__--
-10
-20
-30
* Below40°F(4°C)the useof SAE30 will resultin hardstarting.
** Above80°F(27°C)the useof 10W30maycauseincreased oil
consumption.Checkoil levelmorefrequently.
O
OTICE Synthetic oil meeting ILSAC GF-2,API
certification mark and API service symbol with
"SJ/CF ENERGYCONSERVING" o r higher, is an
acceptable oil at all temperatures. Use of synthetic oil
does not alter required oil change intervals.
Checking Oil Level
Oil level should be checked prior to each use or at least every
8 hours of operation. Keep oil level maintained.
1.
Make sure pressure washer is on a level surface.
2.
Removeoil dipstick and wipe dipstick with clean cloth.
Replaceand tighten dipstick. Removeand and check oil
level.
3.
Verify oil is at FULL mark (top hole) on dipstick. Replace
and tighten dipstick.
Full
Adding Engine Oil
1.
Make sure pressure washer is on a level surface.
2.
Checkoil level as described in Checking Oil Level
3.
If needed,slowly pour oil into oil fill opening to the FULL
mark on dipstick. DO NOT overfill.
NOTICE Overfilling with oil could cause the engine to not
start, or hard starting.
• DONOToverfill.
• If overthe FULLmarkon dipstick,drainoil to reduceoil levelto
FULL mark on dipstick.
4.
Replaceand tighten dipstick.
Changing Engine Oil
if you are using your pressure washer under extremely dirty
or dusty conditions, or in extremely hot weather, change oil
more often.
A CAUTION
Avoid prolonged or repeated skin contact
with used motor oil.
• Used motor oil has been shown to causeskin cancer in certain
laboratory animals.
• Thoroughly wash exposed areas with soap and water.
KEEPOUT OFREACHOF CHILDREN.DON'T
POLLUTE.CONSERVE RESOURCES. RETURN
USEDOIL TO COLLECTION CENTERS.
18
Tabla de contenido
