Maintenance Storage And Transportation; Disposal And Recycling - ADEO Services DYM1851EP Manual Del Usuario

7. MAINTENANCE, STORAGE AND TRANSPORTATION
Before and after each use, check the product and accessories for wear and damage. If required,
exchange them for new ones as described in this instruction manual. Observe the technical
requirements. Check the level of the fuel and engine oil before each use, add the fuel and the
engine oil if it is under the low lever.
Please refer to the B&S operator's manual for the maintenance of the engine parts.
WARNING! Wear protective gloves when working on the cutting device and close to it!
Use proper tools to remove debris! Never use your bare hands!
WARNING! Always use original spare parts for replacement. Do not attach any other
type of cutting device!
WARNING! The replacement of the cutting device should be done by an experienced
user! Rework or sharpening blades is not recommended unless it is done by a repair
service or a similarly qualified specialist!
1. Keep the deck and cutting device clean and free of debris. Remove clippings from the
discharge chute.
2. Check all nuts and bolts periodically for tightness before operation. After prolonged use,
especially in sandy soil conditions, the cutting device will become worn and lose some of
the original shape. The cutting efficiency will be reduced and the cutting device should
be replaced.
3. Keep the cutting device sharp to ensure a good cutting performance. Replace a worn or
damaged cutting device with a new one of the same type or have it sharpened by a qualified
specialist.
4. Replace the cutting device with a new one of the same type.
5. Lubricate the cutting device after each use to prolong the life span of cutting device and
product. Apply light machine oil along the edge of the cutting device.
6. Inspect the grass catcher before each use. Do not use it if you find any damage.
7. Clean the grass catcher after operation using water and mild soap.
8. Let the grass catcher dry thoroughly before storing to avoid mildew.
9. Check the performance of the wires before each use. Ask a qualified specialist to adjust it
if necessary.
Storage:
The following steps should be taken to prepare lawn mower for storage.
1. Empty the tank if you are not going to use the product for an extended period of time
(more than 30 days) and before storing it for the winter.
a) Empty the petrol tank with a suction pump.
EN
Original instructions
210
7. MAINTENANCE, STORAGE AND TRANSPORTATION
CAUTION! Do not drain the petrol in closed rooms, in close proximity of open fire, etc.
Do not smoke! Petrol fumes can cause explosion or fire.
b) Start the engine and let it run until it has used up all remaining petrol.
c) Disconnect the spark plug.
2. Clean and grease the lawnmower carefully.
3. Slightly grease the cutter to avoid corrosion.
4. Store the lawnmower in a dry, clean and frost-protected place, out of reach of
unauthorized persons.
5. Always store the product in a place that is inaccessible to children. The ideal storage
temperature is between 10°C and 30°C.
CAUTION! The engine must have completely cooled down before storing the lawnmower.
NOTE:
- When storing any type of power equipment in an unventilated or material storage shed, care
should be taken to rust-proof the equipment. We recommend using the original package
for storage or covering the product with a suitable cloth or enclosure to protect it against dust.
- Be careful not to bend or kink cables.
Transportation
1. Switch the product off and allow the engine to cool down.
2. Disconnect the spark plug wire and empty the fuel tank according to the instructions in the
engine manual. If not, the fuel could flow down and soiled the floor of the vehicles.
3. Attach transportation guards, if applicable.
4. Always transport the product by its handle.
5. Ensure not to bend or damage the cutter when pushing the lawnmower over obstacles.
6. Protect the product from any heavy impact or strong vibrations which may occur during
transportation in vehicles.
7. Secure the product to prevent it from slipping or falling over, damage and injury.

8. DISPOSAL AND RECYCLING

Be environmentally friendly. Return the tool, accessories and packaging to a recycling centre
when you have finished with them.
Do not put it in the domestic waste.
Original instructions
211
EN