Q-Connect Q20 JAM FREE Manual De Instrucciones página 3

R REVERSE:
In the unlikely event of a paper jam, the reverse setting can
be used to help clear the cutters of paper that has not passed
through. Never attempt to clear a jam by using the reverse
function until you have emptied the wastebasket.
F FoRWARD:
The forward setting can also be used to help clear the cut-
ters in the event of a paper jam.
This allows to manually activate the shredder into cutting
mode.
2) PAPER / CREDIt C ARD EntRy
toUCHGUARD ADVAnCED SAFEty tECHnoloGy
This particular model is equipped with
an advanced safety technology. The
shredder stops immediately when
the TouchGuard sensor is touched.
Shredding will resume automati-
cally once your hand moves away
from the sensor.
JAMFREE® ADVAnCED AntI-JAM tECHnoloGy.
This particular model is equipped with an advanced JamFree anti-
jam technology. When too many sheets are inserted, the Jam-Free
sensor detects over capacity and shredding will NOT START to pre-
vent paper jams.
The JamFree indicator light turns ON to advise users to remove ex-
cess paper. To resume shredding insert less sheets.
AUto-REStARt FEAtURE
This particular model is equipped with an Auto-restart feature. When
the shredder is in off-mode, shredding will resume automatically by
simply inserting paper without powering up.
EnERGy SAVInG AUto PoWER-oFF FEAtURE
This particular model is equipped with an Auto-power-off feature.
The shredder will automatically shut off after 5-6min of non-use to
save energy.
notE:
• Always turn off and unplug the shredder when not in use.
• Thes shredder wil shred staples and small paper clips. It is rec-
ommended that you remove paper clips whenever possible to
extend the lifespan of your shredder.
• Only shred credit cards by feeding them vertically into the mid-
dle of the entry, releasing when shredding begins. Never feed
more than one credit card at a time.
3) lED StAtUS InDICAtoRS:
PoWER on:
The Green LED light indicates the shredder is "ON" and ready to op-
erate when paper is inserted.
3
oVERHEAt:
The Red LED light indicates the shredder has shred continuously
beyond the maximum running time and overheating, the unit will
automatically shut off. If this happens, switch the shredder Off for 50
minutes or longer before resuming normal operation.
oVERloAD:
The Red LED light indicates when too much paper is inserted. Use
the "Reverse" mode to back up and reduce the number of sheets.
DooR oPEn:
The Red LED light indicates the shredder basked is not pushed in
properly. Shredders with pull-out wastebaskets feature a safety
power cut off upon bin removal. Make sure the pull-out wastebas-
ket is properly set back into place and the green "Power On" indica-
tor is lit.
BIn FUll:
When the basket is full, the RED light will indicate it needs to be
emptied. While lit the shredder will be inoperable until the waste-
basket is cleared.
FEAtURES A CD/DVD DEStRoyER:
Do not hold CD/DVD with finger through the center ring while
feeding into the shredder. Serious injury may occur.
Never feed more than one credit card or
CD/DVD at a time.
1) Hold the CD/DVD by the edge and
feed one at a time, releasing when
shredding begins.
2) Shredder will stop when the entire
disc has been destroyed.
MAIntEnAnCE
Warning: Failure to properly maintain
your shredder will void the warranty.
Oil the shredder blades every month
with basic vegetable, cooking oil or
shredder oil. Follow oiling procedure
below. It helps to keep the shredder
blades operating well over many years
of use.
oIlInG PRoCEDURE:
1. Turn off shredder.
2. Apply shredder oil across paper entry.
3. Turn shredder in reverse mode for 3~5 seconds.
CAUtIon:
• Do not spray or keep any aerosol
products in or around shredder.
• DO NOT USE CANNED AIR ON
SHREDDER.
t
shredder
Oil
W W W . Q - C O N N E C T . C O M