Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
Note: the buttons on the control panel mirror
the buttons on the remote control.
On/Off: Press Once On Your Control
•
Panel Or Remote To Turn Your Fan On Or
Off. The Temperature Of The Room Will
Display In The Led Display Panel.
Fan Speed: To Turn The Fan Speed Up Or
•
Down, Either Press The Fan Speed Button
On The Remote Or On The Control Panel.
The Speed Indicator On The Led Display
Will Change To Reflect The Setting.
Oscillation: Press Once On Your Remote
•
Or Control Panel To Start Or Stop Fan
Oscillation.
Modes: Press The Mode Button On Your
•
Remote Or On The Control Panel To Set
One Of Three Modes. When A Mode
Is Active, It Will Illuminate On The Led
Display.
Fan Mode: The Fan Power Will Remain
•
Steady In One Of The Three Speed
Settings.
7 | English
Natural Mode: Natural Mode Is Designed
•
To Mimic The Natural Flow Of Wind
And Will Transition From High Speed
(For Five Seconds), To Mid Speed (For
Five Seconds), To Low Speed (For Five
Seconds). This Cycle Will Repeat.
Night Mode: Night Mode Slowly Reduces
•
The Fan Speed Until It Turns Off To Save
Energy As You Sleep. Once Activated,
The Fan Speed Will Function On High
Speed For 30 Minutes, And Will Then
Reduce To Mid Speed For 30 Minutes
And Low Speed For 30 Minutes Before
Switching Off.
Child Mode: Child Mode Quickly
•
Reduces The Fan Speed Until It Turns
Off To Save Energy. Once Activated A
Timer Will Be Set For 3 Hours. The Fan
Speed Will Function On High Speed For
15 Minutes, And Will Then Reduce To Mid
Speed For 15 Minutes Before Running On
Low Speed For The Remainder Of The 3
Hour Timer. After 3 Hours Have Passed,
The Fan Will Turn Off.
Timer: You Can Set Your Fan To Turn
•
Off Automatically In 1 Hour Increments
From 1-12 Hours. To Do This Press The
Timer Button On Your Remote Or Control
Panel Until The Correct Time Displays On
The Led Display. To Turn This Mode Off,
Continue Pressing The Timer Button Until
The Led Display Reverts Back To The
Temperature
USER SERVICING INSTRUCTIONS
Replaceable Fuse
1.
Grasp plug and remove from the
receptacle or other outlet device. Do not
unplug by pulling on cord.
2.
Open fuse cover by using your thumb or
a flathead screwdriver to slide open fuse
access cover on side of the plug.
3.
Remove fuse carefully by using a small
screwdriver to pry the fuse out of the
compartment by the metal ends of the
fuse.
4.
To avoid the risk of fire, replace fuse only
with 2.5 Amp, 125 Volt fuse.
5.
Close fuse cover by sliding the fuse access
cover back to the plug.
CAUTION: DO NOT ATTEMPT TO REPLACE
THE PLUG ITSELF. DISCARD THE PRODUCT
ENTIRELY IF THE PLUG ITSELF IS
DAMAGED.
Fuse
Fuse Cover
CLEANING & STORAGE
WARNING: ALWAYS TURN THE
APPLIANCE OFF, UNPLUG THE POWER
CORD FROM THE ELECTRICAL OUTLET
BEFORE HANDLING OR CLEANING IT.
CAUTION: DO NOT ALLOW WATER OR
OTHER LIQUIDS TO RUN INTO THE
INTERIOR OF THE APPLIANCE, AS
THIS COULD CREATE A FIRE AND/OR
ELECTRICAL HAZARD.
CAUTION: DO NOT USE ANY ABRASIVE
CLEANERS OR SOLVENTS, AS THIS WILL
DAMAGE THE APPLIANCE.
•
Clean the exterior surface of the appliance
by wiping it with a soft, damp cloth. Dry
the appliance with a soft clean cloth.
•
To store your product out of season, we
recommend using the original or similar
size box.
•
Do not kink or wrap the power cord and
plug around the appliance, as this may
cause the insulation to weaken or split,
particularly where it enters the appliance.
•
Store the appliance in a safe, clean and dry
place when not in use.
FCC STATEMENT
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation. Warning: Changes or modifications
not expressly approved by the party responsible
for compliance could void the user's authority
to operate the equipment.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
English | 8
Tabla de contenido
