cecotec FAST&FURIOUS 5055 PRO Manual De Instrucciones página 12

ENGLISH
Plug the device into a power supply.
Set the steam regulator to the "0" position.
The "Self-checking " function will activate, and the light indicator will flash for 20 seconds
approx.
The device will automatically switch to the All textiles mode, and the corresponding light
indicator will light up, indicating that the iron is heating up.
When the iron is ready to use, the light indicator will remain steady on.
Setting the temperature
Start by ironing the fabrics that require the lowest ironing temperature. Check the recommended
ironing temperature on the label on the garment.
Press the temperature button on the handle repeatedly to change the ironing temperature and
mode.
Press twice each time to switch mode.
The corresponding light indicator will turn on. When the iron is ready to use, the light indicator
will remain steady on.
Setting the steam
The steam regulator is used to adjust the of steam produced when ironing. The recommended
position of the steam regulator for each temperature setting is as following: Fig. 2.
Note: For better ironing results, iron the last strokes without steam to dry the garment.
Steam burst function
This function can be used to remove stubborn creases or to press in a sharp crease or pleat.
Set the temperature to "max".
Press the steam burst button repeatedly with intervals of at least 5 seconds.
Vertical steam
Vertical steam can be used to remove creases from hanging clothes, curtains etc.
Set the temperature to "max".
Hang article of clothing on a clothes hanger.
Operate the iron in a vertical position at a distance of 10 cm/4 in and press the steam burst
button repeatedly with pauses of at least 5 seconds.
Note: If the Auto shut-off light indicator flashes while ironing in a vertical position, it means
that the handle is not properly gripped, and the iron will cool down. Grip the handle correctly in
such a way that the light indicator remains lit permanently.
Spray
Spray can be used to remove stubborn creases.
When ironing, press the spray button and water will spray out of the spray nozzle onto the
garment.
22
FAST&FURIOUS 5055 PRO
Note: Do not use the spray function with silk.
All textiles mode
This mode sets an appropriate temperature, which is suitable for all fabrics that can be
ironed and prevents clothes from becoming damaged due to an unsuitable temperature being
selected. Note: The All textile mode does not apply to fabrics that cannot be ironed.
Check the garment care label for details or try ironing on a part of the fabric not visible.
Press the temperature icon on the handle twice to change the setting.
Auto shut-off function
This function switches off the iron when it is left unattended, increasing security and saving
energy.
While the handle is gripped, the iron heats up. The Auto shut-off light indicator will remain lit
continuously.
When the handle is released, the Auto shut-off function is activated, the iron stops heating and
the Auto shut-off light indicator will flash.
Anti-drip function:
This system controls the water flow to the soleplate at all times. Below a certain temperature,
the anti-drip function cuts off the flow of water and stops the iron from dripping onto the
fabric.
Descaling
The anti-calc function is a permanent system located inside the water tank to eliminate
impurities from the water and to reduce the problems connected with limescale build-up.
To prolong the efficiency of this system, follow these steps occasionally:
Unplug the iron and allow it to cool down.
Fill 3/4 of the measuring cup with water. Add 1 teaspoon of salt to the water and fill the water
tank with this solution.
Leave the solution in the water tank for 15 minutes, shaking occasionally, and then empty it.
Fill the water tank a second time with saltwater solution, shaking occasionally and empty it
again after 15 minutes.
Fill the tank with fresh water to rinse and empty.
After ironing
Unplug the iron from the power supply.
Empty the water tank.
Switch the steam regulator clockwise and back again several times (self-cleaning). Set the
steam regulator to the "0" position.
Each time the steam regulator is used, the Self-clean system cleans the mechanism of scale
ENGLISH
23
FAST&FURIOUS 5055 PRO